manualshive.com logo in svg

Memotec NetPerformer SDM-9120 Series, Руководство по установке оборудования

Поделиться
Скачать
Memotec NetPerformer SDM-9120 Series Скачать руководство пользователя страница 122

NetPerformer Hardware Installation Guide

5-6

 Memotec Inc. 

5.5

WAN/User Port Specifications

•

1 built-in serial port, configurable as user or link, supporting V.35/V.11, TIA-232 
(V.24), X.21, X.21 EU, TIA-449 (V.36) and TIA-530 interfaces.

•

Maximum speed without compression: 6 Mbps (6144 Kbps).

For a port with INTERNAL clocking, if the port speed is configured higher 
than 2 Mbps (2048 Kbps), the clock speed will be 3 Mbps (3072 Kbps) or 6 
Mbps (6144 Kbps), whichever is closer to the configured speed. For 
EXTERNAL clocking all port speeds are supported.

•

Link port maximum speed with compression: 896 Kbps.

•

HD-26 female connectors, gender and interface autodetect from custom HD-26 
cables: V.35 DCE, V.35 DTE, X.21 DCE, X.21 DTE, X.21 EU DCE, X.21 EU DTE, 
TIA-232 DCE, TIA-232 DTE, TIA-449 DCE, TIA-449 DTE, TIA-530 DCE, TIA-530 
DTE.

•

Circuits: either leased, switched or Frame Relay.

•

Coding: NRZI or NRZ.

•

WAN port protocols: synchronous full-duplex HDLC, Frame Relay (FR-USER for 
network connection), RFC-1490.

•

Synchronous user port protocols: HDLC, Synchronous PPP.

•

Frame Relay protocols: Frame Relay User (FR-USER), Frame Relay Network 
(FR-NET), RFC-1490, UNI-DTE, UNI-DCE.

•

Frame Relay management: LMI, ANSI TI.617/Annex D, ITU-T Q.933/Annex A, 
CLLM or disabled.

•

PVC switching: 300 PVCs, automatic DLCI discovery.

•

SVCs: Frame Relay telephony applications, one SVC per voice call.

•

SNA: SDLC, LAN or Frame Relay RFC1490 (BAN, BNN); SDLC spoofing of up 
to 64 PUs, type 1, 2.0, 2.1 and 4/5, local SDLC and LLC2 spoofing, SDLC-to-
LLC2 conversion.

•

Asynchronous user port protocols: ENQ/ACK, XON/XOFF, CTS/DTR, 
Transparent, Reliable, Asynchronous PPP.

Содержание NetPerformer SDM-9120 Series


































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды