Memotec NetPerformer SDM-9120 Series Скачать руководство пользователя страница 121

Страница: 121 / 161

Serial Port and User Equipment Connections

Memotec Inc.

5-5

5.4

Connecting the User Equipment

►

To connect the user equipment to the serial port:

Locate the HD-26 custom cable that is appropriate for:

The device you are attaching: DTE or DCE

The interface you want to use: V.35/V.11, TIA-232 (V.24), X.21, X.21 EU, TIA-
449 (V.36) or TIA-530.

Connect the male end of the HD-26 cable to a serial port on the SDM-9XXX Series
unit.

Connect the other end of the cable to the user device (CSU/DSU, modem, router,
front end processor, etc.).

5.4.1

Activating the User Equipment Connection

►

To activate the user equipment connection:

Configure all parameters and options for the connection. Refer to the

NetPerformer

Reference Guides

, which is included on the

NetPerformer Documentation CD

Activate a data connection by bringing up the connected user equipment.

Activate a voice connection by dialing a speed dial number to place a call.

Check the status of the NetPerformer, its connections and all active channels, ports,
PVCs and SVCs by executing the statistics commands (refer to the

NetPerformer

Reference Guides

for details).

Caution

Do not connect a data port (WAN/user) to a host, PU, or Frame Relay
device until you have configured the port protocol via the software.
Refer to the

NetPerformer Reference Guides

for details.

Caution

Configure the E&M interface type

before you connect the cables to

ports on the E&M interface card

. Otherwise, the interface card could

be damaged. FXO, FXS and digital voice channels can be configured
before or after cable connection.

Содержание NetPerformer SDM-9120 Series


































































































































































Результаты поиска

Содержание NetPerformer SDM-9120 Series

Отзывы:

Бренды по названию

Популярные бренды

Memotec NetPerformer SDM-9120 Series, Руководство по установке оборудования

Результаты поиска

Содержание NetPerformer SDM-9120 Series

Отзывы:

Бренды по названию

Популярные бренды