Meltem M-WRG-II Series Скачать руководство пользователя страница 5

Страница: 5 / 14

Dismantling instructions

Ventilation units from the M-WRG-II series

- 5 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

Tools and equipment required

— Set of cross-head screwdrivers

— Set of slotted screwdrivers

— Torx screwdriver TX10

— Torx screwdriver TX20

Dismantling the ventilation unit

4.1

Detach electrical connections and uninstall the ventilation unit

DANGER

Potentially fatal voltages

—

Only qualified electricians may work on the electrical installation.

— The VDE regulations or any special safety regulations applicable in your country

apply to the electrical installation work.

►

Before starting to uninstall, disconnect the mains cable and the control cable (if

used) on all poles from the main power supply.

► Observe the five safety rules (DIN VDE 0105-100, EN 50110-1) for working on elec

trical systems:

— Disconnect from mains (all-pole disconnection of a system from live parts)

— Secure against reconnection

— Check that the system is voltage-free

— Earth and short-circuit

—

Cover or block off access to adjacent live parts

►

Detach the electrical connections from the ventilation unit.

►

Uninstall the ventilation unit from its installation location.

►

Place the ventilation unit on a suitable work surface for the rest of the dismantling

work.

Содержание M-WRG-II Series















Результаты поиска

Содержание M-WRG-II Series

Отзывы:

Похожие инструкции для M-WRG-II Series

Бренды по названию

Популярные бренды

Meltem M-WRG-II Series, Инструкция по разборке

Результаты поиска

Содержание M-WRG-II Series

Отзывы:

Похожие инструкции для M-WRG-II Series

Бренды по названию

Популярные бренды