Meltem M-WRG-II E-F Скачать руководство пользователя страница 33

Страница: 33 / 60

Operating and installation instructions

M-WRG-II P-T (-F, -FC), M-WRG-II E-T (-F, -FC) ventilation units

- 33 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

11 Options for ventilation mode

11.1

External control input

11.1.1 Description

With the external control input supplied as standard, the M-WRG-II unit has an additional

input terminal for 230 V AC (working voltage range: 85 V AC to 265 V AC / 50-60 Hz) to

which a switch, time switch, motion detector or similar may be connected.
The external control input is equipped with a time-delay relay that can be used to set a

switch-on delay and a run-on time:

— Switch-on delay:

the M-WRG-II unit does not start until the set time has elapsed.

— Run-on time:

the M-WRG-II unit does not switch to the previously active ventilation program until

the set time has elapsed.

Windowless rooms can be ventilated in accordance with DIN 18017-3 in combination with

the M-WRG-II O/NOF option, part no. 721004.

11.1.2 Factory defaults and possible adjustment ranges

Parameter

Factory defaults

Possible adjustment ranges

Air flow

60 m

10 to 100 m

Switch-on delay

1 min

0 to 240 min

Run-on time

15 min

0 to 240 min

NOTICE

The above parameters can be changed either at the factory or using the optional wire-

less remote control M-WRG-FBH.

11.1.3 M-WRG-II O/EST-1, part no. 721005, and M-WRG-II O/EST-2, part no. 721006

The following options may be selected in addition to the external control input which is

supplied as standard:

— M-WRG-II O/EST-1: without switch-on delay, needs to be fitted at the factory

— M-WRG-II O/EST-2: without run-on time, needs to be fitted at the factory

11.2

M-WRG-II O/PARM, part no. 721000

This option is used to set special air output parameters for all M-WRG-II units. It needs to

be fitted at the factory.

Содержание M-WRG-II E-F





























































Результаты поиска

Содержание M-WRG-II E-F

Отзывы:

Похожие инструкции для M-WRG-II E-F

Бренды по названию

Популярные бренды

Meltem M-WRG-II E-F, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание M-WRG-II E-F

Отзывы:

Похожие инструкции для M-WRG-II E-F

Бренды по названию

Популярные бренды