Mellanox Technologies Grid Director 4700 Скачать руководство пользователя страница 42

Страница: 42 / 88

Packing and Unpacking

Packing and Unpacking

This chapter provides step-by-step instructions for packing and unpacking the Grid Director
4700 chassis.

4.1

Package Contents

The Grid Director 4700 is supplied in a heavy duty tri-wall cardboard box secured with
packing straps.

For information about the various 4700 configurations and items shipped with the chassis,
refer to

Chapter 1

(on page

The basic 4700 shipping contents are as follows:



Grid Director 4700



Horizontal fan unit (sFU-40H)



Vertical fan unit (sFU-40V)



Management board (sMB-CM)



Two power supply units (sPSU-S).

The Grid Director 4700 chassis is shipped with a horizontal fan unit (sFU-40H) and a vertical
fan unit (sFU-40V) installed at the front of the chassis and two power supplies at the rear of the
chassis.

Additional components include:



Rail kit for rack installation



Cabling guide brackets



One power cord per power supply



One console cable



A grounding kit



Mellanox Getting Started Short Guide



Two product CDs (one containing the software, one containing the documentation).

Verify that the package contains the items detailed in the packing list before you begin to
install the Grid Director 4700.

Check for loose parts or any visible damage to the contents. If any damaged or missing parts
are detected, notify your local Mellanox representative.

Содержание Grid Director 4700

























































































Результаты поиска

Содержание Grid Director 4700

Отзывы:

Похожие инструкции для Grid Director 4700

Бренды по названию

Популярные бренды

Mellanox Technologies Grid Director 4700, Руководство по установке

Результаты поиска

Содержание Grid Director 4700

Отзывы:

Похожие инструкции для Grid Director 4700

Бренды по названию

Популярные бренды