Mellanox Technologies Grid Director 4700 Скачать руководство пользователя страница 34

Страница: 34 / 88

4700 Specifications

Indication

LED Description

Remarks

ON – Vertical and Horizontal fan unit fault indication.
Indicates that at least one of the 13 fans has failed.

Temp (Orange)

OFF – Indicates normal temperature levels.

ON – Indicates an over-temperature fault on the chassis.

Temp (Orange)

FM Active (Green)

OFF - Fabric Manager is not active

ON - Fabric Manager running on the Management
Board

Blink - Fabric Manager is standby on the Management
Board

DM Active (Green)

OFF - Device Manager is not active

ON - Device Manager running on the Management
Board

Power (Green)

HW Only

OFF – indicates a problem in power supply to the board

ON – indicates that all board voltage levels are
operating normally

Info (Blue)

User only

General purpose LED for management use

OFF – No attention required

Blinking – Chassis attention required

PSU OK (Green)

OFF – N/A

ON – System Power OK

Blinking – System Power problem

AC-DC power supply fault
indication. Indicates that at
least one of the main AC-DC
power supplies has an AC or
DC fault

Eth—1 and 2

Two LEDs: Link (Green) and Activity (Orange)

Eth—1 and 2

3.15.5

sFU-40H Horizontal Fan Unit LEDs

Table 21: sFU-40H Horizontal Fan Unit LEDs

Indication

LED Description

Remarks

Temp (Orange)

ON – Indicates an over-temperature fault on the
chassis.

OFF – Indicates normal temperature levels.

sFU-40V (Orange)

ON – Vertical fan unit fault indication. Indicates that
at least one of the five fans in the vertical fan unit has
failed.

OFF – All fans in the vertical fan unit are OK.

sFU-40H (Orange)

ON – Horizontal fan unit fault indication. Indicates
that at least one of the eight fans in the horizontal fan
unit has failed.

OFF – All fans in the horizontal fan unit are OK.

PS (Orange)

AC-DC power supply fault indication.

ON – Indicates that at least one of the main AC-DC
power supplies has an AC or DC fault.

OFF – All PSUs are OK.

Содержание Grid Director 4700

























































































Результаты поиска

Содержание Grid Director 4700

Отзывы:

Похожие инструкции для Grid Director 4700

Бренды по названию

Популярные бренды

Mellanox Technologies Grid Director 4700, Руководство по установке

Результаты поиска

Содержание Grid Director 4700

Отзывы:

Похожие инструкции для Grid Director 4700

Бренды по названию

Популярные бренды