Mellanox Technologies Grid Director 4700 Скачать руководство пользователя страница 33

Страница: 33 / 88

Mellanox Grid Director 4700 Installation Manual

Indication

LED Description

Remarks

User only

OFF – No attention required

Blinking – Chassis attention required

Card Ready (Green)

OFF – Card not Ready

ON – Card ready

Blinking Slowly – Card loading

Blinking Fast – Card problem

3.15.3

HyperScale Fabric Board (sFB-4700-2X) LEDs

Table 19: HyperScale Fabric Board (sFB-4700-2X) LEDs

Indication

LED Description

Remarks

Link

18 Green LEDs

HW only

Each LED indicates the state of ports of each Line
Board.



ON – indicates physical link up



OFF – no link detected



Blinking – indicates errors

18 pairs of internal link
indication LEDs. Each LED
indicates the state of two ports
of each Line Board.

CXP Link

36 Amber LEDs

36 Green LEDs

HW only

The two LEDs in each pair are as follows:



Green – ON indicates physical link up



Amber – ON indicates logical link up

The LED states are as follows:



OFF – no link detected



ON – the port has a link



Blinking:

Green – indicates errors

Amber – indicates data activity

Indicates the state of the 36
external QSFP port
connectivity.

Power (Green)

HW only

ON – indicates that all board voltage levels are
operating normally

OFF – indicates a problem in power supply to the
board

Info (Blue)

User only

General purpose LED for management use

OFF – No attention required

Blinking – Chassis attention required

Card Ready
(Green)

OFF – Card not Ready

ON – Card ready

Blinking Slowly – Card loading

Blinking Fast –Card problem

3.15.4

Management Board (sMB-CM) LEDs

Table 20: Management Board (sMB-CM) LEDs

Indication

LED Description

Remarks

Fans (Green)

OFF – All fan drawers are OK.

Two fan drawers

Содержание Grid Director 4700

























































































Результаты поиска

Содержание Grid Director 4700

Отзывы:

Похожие инструкции для Grid Director 4700

Бренды по названию

Популярные бренды

Mellanox Technologies Grid Director 4700, Руководство по установке

Результаты поиска

Содержание Grid Director 4700

Отзывы:

Похожие инструкции для Grid Director 4700

Бренды по названию

Популярные бренды