Mellanox Technologies Grid Director 4700 Скачать руководство пользователя страница 32

Страница: 32 / 88

4700 Specifications

3.15.1

sLB-4018 Line Board LEDs

Table 17: sLB-4018 Line Board LEDs

Indication

LED Description

Remarks

Link State

18 Amber LEDs

18 Green LEDs

HW only

The two LEDs in each pair are as follows:



Green – ON indicates physical link up



Amber – ON indicates logical link up

The LED states are as follows:



OFF – no link detected



ON – the port has a link



Blinking:

Green – indicates errors

Amber – indicates data activity

Indicates the state of the
QSFP connectivity.

Power (Green)

HW only

ON – indicates that all board voltage levels are
operating normally

OFF – indicates a problem in power supply to the board

Info (Blue)

User only

General purpose LED for management use

OFF – No attention required

Blinking – Chassis attention required

Card Ready (Green)

OFF – Card not Ready

ON – Card ready

Blinking Slowly – Card loading

Blinking Fast – Card problem

3.15.2

Fabric Board (sFB-4700) LEDs

Table 18: Fabric Board (sFB-4700) LEDs

Indication

LED Description

Remarks

Link

18 Amber LEDs

18 Green LEDs

HW only

Each pair of LEDs indicates the state of ports of each
Line Board.

The two LEDs in each pair are as follows:



Green – ON indicates physical link up



Amber – ON indicates logical link up

The LED states are as follows:



OFF – no link detected



ON – link detected



Blinking:

Green – indicates errors

Amber – indicates data

18 pairs of internal link
indication LEDs. Each
pair of LEDs indicates
the state of two ports of
each Line Board.

Power (Green)

HW only

ON – indicates that all board voltage levels are operating
normally

OFF – indicates a problem in power supply to the board

Info (Blue)

General purpose LED for management use

Содержание Grid Director 4700

























































































Результаты поиска

Содержание Grid Director 4700

Отзывы:

Похожие инструкции для Grid Director 4700

Бренды по названию

Популярные бренды

Mellanox Technologies Grid Director 4700, Руководство по установке

Результаты поиска

Содержание Grid Director 4700

Отзывы:

Похожие инструкции для Grid Director 4700

Бренды по названию

Популярные бренды