Mellanox Technologies Grid Director 4700 Скачать руководство пользователя страница 30

Страница: 30 / 88

4700 Specifications

Configuration

Modules Included

Power (Watts)

Heat Output
(BTUs)

324 ports QSFP copper

9 sFB-4700, 18 sLB-4018, 1 sFU-40H, 1
sFU-40V, 2 sMB, 3 sPSU-S

4,244W

14,479

324 ports QSFP
HyperScale Fabric Boards

9 sFB-4700x2, 18 sLB-4018, 1 sFU-40H, 1
sFU-40V, 2 sMB, 4 sPSU-S

5,279W

18,010

3.11

Maximum Heat Dissipation

Table 12: Maximum Heat Dissipation

Maximum heat dissipation

(max. for full configuration)

22,206 BTU/Hour

3.12

Airflow

Table 13: 4700 Airflow

Rated volumetric air flow for a fully configured chassis.

1300 CFM (Cubic Feet per Minute)

3.13

Physical Characteristics

Table 14: 4700 Physical Characteristics

4700 Features

Characteristics

19" rack mountable chassis

19U height

Dimensions

Width - 19" (440 mm)

Depth - 22.75" (578 mm)

Height - 25.6" (650 mm)

Weight

128 to 163 lbs (58 to 74 kg), depending on configuration

Minimum rack depth required for the rail kit

N/A

Maximum rack depth required for the rail kit

N/A

Table 15: HyperScale Physical Characteristics

HyperScale Features

Characteristics

HyperScale rack mountable chassis

20U height

3.14

Weights and Dimensions

Table 16: Weights and Dimensions

Metric (2)

English (1)

Unpacked Modules

D (cm)

W (cm)

H (cm)

D (in)

W (in)

H (in)

Lbs

Packed Modules

sMB-CM

4.5

1.1

8.7

1.77

2.42

7.5

1.4

15.7

Содержание Grid Director 4700

























































































Результаты поиска

Содержание Grid Director 4700

Отзывы:

Похожие инструкции для Grid Director 4700

Бренды по названию

Популярные бренды

Mellanox Technologies Grid Director 4700, Руководство по установке

Результаты поиска

Содержание Grid Director 4700

Отзывы:

Похожие инструкции для Grid Director 4700

Бренды по названию

Популярные бренды