Meler STARBI Скачать руководство пользователя страница 29

Страница: 29 / 73

MA-5151-ENG

PATTERN CONTROLLER STARBI

USE

4-1

4. USE

This section explains how to use the pattern controller. Although its operation

is very user-friendly, it should not be used by untrained personnel.

Warning:

Improper use may damage the unit itself or injure the person

using it.

Start-up and automatic process

When turning on the switch on the rear, the GREEN POWER LED remains lit.

The unit is powered but the screen remains off.

Note:

When the unit is turned on, it starts in STOPPED mode. Even if a product

is selected, the outputs are not activated.

When the ON/OFF button is pressed, the screen turns on and the POWER LED

stays on.

Manual change from RUNNING mode to STOPPED mode

In STOPPED mode, the RED LED of the button remains on. To start producing

press the STOP button. The RED LED goes off and the unit switches to READY

mode.

If the conditions for producing are met, it automatically switches to RUNNING

mode (central GREEN LED on) and the product selected in the program will

start to be produced.

Every time STOP is pressed, the system changes from STOPPED to RUNNING

status and vice versa.

Automatic change from RUNNING mode to STOPPED mode

Through Modbus/Profibus communication, it is possible to make the

automatic change from one mode to another. This is compatible with the

manual mode change.

For more information on Modbus/Profibus communications, see the ‘Modbus

Communication’ and ‘Profibus Communication’ points in this chapter.

STOPPED

MODE

READY

MODE

RUNNING

MODE

Содержание STARBI










































































Результаты поиска

Содержание STARBI

Отзывы:

Meler STARBI, Инструкция по эксплуатации, Страница: 29 / 73

Результаты поиска

Содержание STARBI

Отзывы: