Meler Micron PUR LC Скачать руководство пользователя страница 62

Страница: 62 / 106

MELER GLUING SOLUTIONS

4-28

MELTER OPERATION

ENGRANE

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

: S02101100 v1.0.106

120 s

Charge

3. Charge

Level alarm

Sound on alarm

‘3. Load’ Menu

Esta pantalla permite controlar las diferentes cuestiones relativas a la carga

de adhesivo.

Screen 1: Minimum adhesive level sensor

• Level alarm:

Time after which the unit stops and activates a low-level

alarm.

• Sound with alarm:

Allows you to configure the sensor alarm to emit a

sound

Screen 2: Automatic adhesive feeder

ENGRANE

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

: S02101100 v1.0.106

1 s

60 s

90 s

Charge

3. Charge

Automatic feeder alarm

Sound on alarm

Over charge time

Charge error alarm

Automatic charge

CHARGE

Cover opened alarm

• Automatic feeder:

Activates or deactivates automatic feeding

When you press

‘

CHARGE’, This lets you activate manual loading. When

pressed, it loads, and when released, the loading stops.

• Feeder alarm.

Defines the time that must pass to give an external feed

alarm.

• Overfill time:

This lets you configure for how much time the adhesive

will continue to be loaded once the lower level sensor has activated (tank

sufficiently full, but not completely full).

• Charge error alarm:

This defines the maximum amount of time for filling

the tank. If this time is exceeded, the unit displays an alarm.

• Open tank lid alarm:

An alarm sounds when the tank lid is open and it

stops loading immediately.

• Buzzer:

This lets you set whether or not loading alarms emit a sound.

ENGRANE

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

: S02101100 v1.0.106

120 s

Charge

3. Charge

Level alarm

Sound on alarm

ENGRANE

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

: S02101100 v1.0.106

15 s

120 s

Charge

3. Charge

Sound on alarm

INJECT

Auto. inject.

Cycle time

Injection time

Screen 3: Dry air/gas injection

• Automatic injection:

Activates or deactivates dry air/gas injection.

By pressing ‘INJECT’, you can activate and deactivate injecting manually.

• Cycle time:

Sets the time that has to elapse between dry air/gas

injections.

• Injection time:

Sets the dry air/gas injection time.

• Sound with alarm:

Allows you to configure the injection system alarms to

emit a sound.

Содержание Micron PUR LC











































































































Результаты поиска

Содержание Micron PUR LC

Отзывы:

Бренды по названию

Популярные бренды

Meler Micron PUR LC, Инструкция по эксплуатации

Результаты поиска

Содержание Micron PUR LC

Отзывы:

Бренды по названию

Популярные бренды