Meler Micron PUR LC Скачать руководство пользователя страница 61

Страница: 61 / 106

MELTER OPERATION

4-27

MA-5184-ENG

PUR LC/MC ADHESIVE MELTER

ENGRANE

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

: S02101100 v1.0.106

DI1

DI2

DI3

DO2

DO3

DO4

2.3 Input / Output

Imput

Output

Standby

COMs OFF

Pump OFF

Temperature OK

Alarms

Adhesive Level

ENGRANE

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

: S02101100 v1.0.106

Are you sure

you want to restore

to the default settings??

YES

2.3 Configuration of input and output signals

This allows you to configure the unit’s digital input and output signals.

The inputs can be:

• ON/OFF:

Switches the unit fully off or on.

• Standby:

Activates or deactivates the Standby mode.

• Activity:

Enables the activity control to measure the times for switching

automatically to Standby and OFF.

• Pumping:

Activates or deactivates the pumping.

• COMM.:

Activates or deactivates the communications.

The outputs can be:

• Standby:

Indicates that the unit is in Standby mode.

• Zones in Temperature OK.

Indicates that all active zones are in tempera-

ture OK.

• Ready.

Indicates that the unit is ready to operate, with temperature OK

and no operating errors.

• Running.

The unit is pumping, with temperature OK and no operating

errors.

• Alarm:

Indicates that there is an active Alarm.

• Level:

Indicates high level of adhesive in the tank.

• No Level:

Indicates low level of adhesive in the tank.

2.4 Restore default values

Allows you to delete all the changes made to the system and leave the unit

with the factory-set default parameters. After pressing, the following confir-

mation message will appear.

When you press ‘YES’, the device restarts with the default configuration.

Содержание Micron PUR LC











































































































Результаты поиска

Содержание Micron PUR LC

Отзывы:

Бренды по названию

Популярные бренды

Meler Micron PUR LC, Инструкция по эксплуатации

Результаты поиска

Содержание Micron PUR LC

Отзывы:

Бренды по названию

Популярные бренды