Meler Micron PUR LC Скачать руководство пользователя страница 56

Страница: 56 / 106

MELER GLUING SOLUTIONS

4-22

MELTER OPERATION

ENGRANE

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

: S02101100 v1.0.106

Manual OFF

T: Tank

External OFF

D: Distributor

1.1: Hose 1

1.2: Applicator 1

2.1: Hose 2

2.2: Applicator 2

3.1: Hose 3

3.2: Applicator 3

4.1: Hose 4

4.2: Applicator 4

5.1: Hose 5

5.2: Applicator 5

6.1: Hose 6

6.2: Applicator 6

Signal 1

Group 1: Robot Arm RIGHT

ENGRANE

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

: S02101100 v1.0.106

-20 °C

5 min

-10 °C

5 min

1.2 Sequential

Enable sequential

Define groups

Group B

Group C

ENGRANE

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

: S02101100 v1.0.106

Sequential group A

T: Tank

D: Distributor

1.1: Hose 1

1.2: Applicator 1

2.1: Hose 2

2.2: Applicator 2

3.1: Hose 3

3.2: Applicator 3

4.1: Hose 4

4.2: Applicator 4

5.1: Hose 5

5.2: Applicator 5

6.1: Hose 6

6.2: Applicator 6

1.3 Inhibitions

This menu allows you to create seven groups of zones and program the mode

in which the Inhibition (Off) can be activated or disabled.

The following is indicated for each group:

• Name of the group.

The name can be changed to identify it more easily.

• Manual inhibition of the group (Manual Off).

Whether it is possible to ma-

nually activate or deactivate the inhibition in that group from the ‘SHORT-

CUTS’ menu.

Manual inhibition takes priority over external inhibition.

• Automatic inhibition with external signal (External Off).

Whether it is

possible to externally activate or deactivate the inhibition in that group.

You must indicate which of the seven possible external signals will per-

form this function.

One signal can never be enabled in two different groups.

• Selected zones.

A zone may be selected in more than one group or may

not be in any grou.

1.2 Sequential Heating

This lets you start heating the zones one after the other. This prevents a zone

from being active for a long time until the slowest zone heats up.

This function allows you to create three heating groups: A, B and C. Press

‘Define groups’ to go to a screen where zones can be added to the groups:

• Group A:

this always includes the Tank, which is the slowest and serves

as a reference for the remainder of the zones. Other zones can be added

so they begin to heat up with the Tank.

• Group B:

other zones can be added and some degrees of temperature

defined before the tank reaches its set point and a wait time.

• Group C:

the zones that are not in group A or B can be added here.

If a component in group B or C is deselected, it goes back to group A. By de-

fault, all the zones belong to group A.

Example:

- Tank set point temperature: 150°C

- Programming of Group B: -20°C / 5 minutes.

Group B begins to heat up 5 minutes after the tank reaches 130°C.

Содержание Micron PUR LC











































































































Результаты поиска

Содержание Micron PUR LC

Отзывы:

Бренды по названию

Популярные бренды

Meler Micron PUR LC, Инструкция по эксплуатации

Результаты поиска

Содержание Micron PUR LC

Отзывы:

Бренды по названию

Популярные бренды