Megger Baker DX страница 61 Скачать руководство пользователя

Страница: 61 / 156

megger.com

7 —

Setting up Fixtures, Test Accessories, and Lead

Connections

Overview of Leads, Fixtures, and Accessories Used in Testing

The following table provides an overview of the test leads or fixture used for each tester

configuration running each specific test type:

Table 2. Leads or fixtures used during testing.

Tester

Configuration

Test Type

Fixture, Accessory,

or Test Leads Used

DX Host

Resistance, inductance,
capacitance.

Low-voltage RLC tester leads.

DX Host

DC tests.

High-voltage tester leads.

DX Host

Surge testing in three-phase coil
mode.

High-voltage tester leads.

DX Host

Surge testing in single-coil mode.

High-voltage tester leads; leads 1
and 2 only.

DX Host

Low-voltage armature or coil tests. Low-voltage test probes (83004)

connected to RLC connector or
low-voltage RLC tester leads.

DX Host

Rotor influence check (RIC) test.

Low-voltage RLC tester leads.

DX Host

Armature span testing.

ATF-4000 fixture.

Power Packs

DC tests; only HiPot and Surge run
from Power Packs. Surge testing in
three-phase mode.

High-voltage power pack leads.
PP40 leads require manual
configuration for three-phase
testing.

Power Packs

Surge testing in single-coil mode.

High-voltage power pack leads.
Leads 1 and 2 only for three-phase
leads.

Power Pack
(PP85 only) or
AT101-ZTX

Low-impedance armature testing. ATF-5000 fixture or

ATP02-P probes.

Power Pack
(PP85 only) or
AT101-ZTX

Low-impedance single-coil testing. ATP02-P probes or

ATP02-C clips.

Содержание Baker DX





























































































































































Результаты поиска

Содержание Baker DX

Отзывы:

Похожие инструкции для Baker DX

Бренды по названию

Популярные бренды

Megger Baker DX, Руководство пользователя

Результаты поиска

Содержание Baker DX

Отзывы:

Похожие инструкции для Baker DX

Бренды по названию

Популярные бренды