background image

 

megger.com 

137 

 

DC and Surge Tests Voltages 

Recommended Test Voltages 

Megger Baker Instruments has a recommended standard (see table) for test voltages for DC tests 
and Surge tests conducted on a motor, generator, or transformer.  That standard is twice the AC 
line voltage plus 1,000 volts.   

This test voltage is consistent with NEMA MG-1, IEEE 95-1977 (for test voltage greater than 
5,000 volts) and IEEE 43-2000 (test voltages less than 5,000 volts). 

View other standards in the tables below for a comparison of IEEE 95, EASA DC-HiPot, IEEE 522 
Surge testing, IEC 34-15, and Megger recommended testing voltages. 

NOTE: The tables list representations of motors, as well as the formulas to calculate voltages so that you can 
calculate test voltage of any size motor. 

 

Table 6.  Megger Baker Instruments recommended voltages. 

V Line 

Per Unit 

In Service, 2E + 1,000 

480 

392 

1,960 

575 

469 

2,150 

600 

490 

2,200 

2,300 

1,878 

5,600 

4,160 

3,397 

9,320 

6,900 

5,634 

14,800 

13,800 

11,268 

28,600 

 

NOTE: Use the “Peak Voltage” value shown on the screen to obtain the proper test voltages. 

 

Table 7.  IEEE 95 for HiPot test. 

V Line 

Per Unit 

Min Test, 

V Line × 1.25 × 1.7 

Max Test, 

V Line × 1.5 × 1.7 

480 

392 

1,020 

1,224 

575 

469 

1,222 

1,466 

600 

490 

1,275 

1,530 

2,300 

1,878 

4,888 

5,865 

4,160 

3,397 

8,840 

10,608 

6,900 

5,634 

14,663 

17,595 

13,800 

11,268 

29,325 

35,190 

 

Содержание Baker DX





























































































































































Отзывы: