CAUTIONS
Before replacement of luminaire or lamp, turn off and allow them to cool down.
Heat-resistant gloves are mandatory when handling the luminaire or lamp.
The minimum safety distance from the illuminated object is 0.1m.
The manufacturer accepts no liability for any damage resulting from the misuse of the
luminaire or from when it is used with inappropriate equipment.
Consult your dealer if you have any enquiries.
Caution to the risk of electric shock during installation or maintenance.
•
•
•
•
•
•
•
GB
8010ZTK03A
Allen
ATTENTION
• Designed for outdoor application.
• Instant start is allowed.
• The operating temperature of the luminaire is -30
°
C to + 40
°
C
.
Please refer to the diagram before installation.
Installation
LED
Correct Disposal of This Product
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device,please use the return and collection systems or contact
the retailer where the product was purchased. They can take this product for environmental safe
recycling.
F51100SM/F51300SM
Instruction Manual
MEGAMAN FONDA
Model Number
Wattage
Voltage
Frequency
Power Factor
IP Rating
10.5W
220-240V~
50/60Hz
>0.5
F51100SM
F13117TA/F13117TK
A4 50g
胶版纸
2013-11-05
IP66
0.1m
---
220-240V~
50/60Hz
>0.5
F51300SM
10.5W
IP66
IK10
IK10
IK Rating
Read the entire manual carefully before installation and operation.
It is recommended that the installation or maintenance be performed by a licensed
and qualified electrician.
DO NOT disassemble the luminaire. Doing so may result in lamp damage or
malfunction.
Switch off the power source before installation, replacement and cleaning.
Wearing gloves during installation is suggested for keeping the lamp in the best
condition.
•
•
4 pcs
PART LIST
A1
A2
4 pcs
A3
4 pcs
M4.5 screw
Screw raw plug
Theft-proof
screw
1 pcs
A4
A5
2 pcs
A6
1 pcs
A7
1 pcs
A8
4 pcs
Theft-proof
screw driver
M3 screw
Wire bushing
Cable gasket
Rubber ring
Outdoor Integrated LED Bulkhead
Ultra Slim LED Downlight
®
TECHNICAL SPECIFICATION
The screws and cover should be installed properly to ensure the waterproof
protection.
•
•
Article Number
MM77110
MM
11
771
Step1
Step2
Step3
Step4
•
1
4
3
2
Push upward to unlock
the light source plate
A3
A4
•
4
1
2
3
Push downward to
lock the light source plate
Secure the luminaire to the wall with the M4.5 screw
, rubber ring
and
the screw raw plug (A2). The screws and cover should be installed properly to
ensure the waterproof protection.
(A1)
(A8)
•
•
Put the
back on one of the studs to ensure the
plate will not dangling freely and prevent wire damage during installation.
light source plate
light source
A2
A8
A1
Remove the ring, cover and light source plate
chip on the light source plate.
for wiring. DO NOT touch the LED
Secure the cable gasket (A7) into the cable entry hole. Pass the power cable
through the cable gasket and fix the power cable with M3 screws
(
A
5)
and
wire
bushing
(
A
6).
IDV GmbH
Birkenweiherstr. 2
D-63505 Langenselbold
Germany
www.megaman.de
A7
Cable entry
hole
Studs
A6
A5
