Mega MMP4 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 96

Mega MMP4 Скачать руководство пользователя страница 43

MMP4-CAT(T4)-MX-2

26 Feb 2014

SECTION 10

Recommended Support Parts

10-2

If your system is not covered in this manual or are having difficulties locating the necessary components please
contact MEGA Corp. Product Support Group at:
US Toll Free: 1-800-345-8889 or
Direct: 1-505-345-2661 or visit our website at www.megacorpinc.com for more detailed contact information.

D. F

RAME

AND

S

USPENSION

G

ROUP

PART DESCRIPTION

PART NO.

QTY

1.

Wheel and Tire Assembly

303933

1

2.

Hitch pin, 1 inch

303935

2

3.

Chain, 3/8 inch, GR 70, 2.4 ft

038453-13

1

4.

Shackle, 3/8 inch

355020

2

5.

Bearing, Wheel, Inner

304157

2

6.

Bearing, Wheel, Outer

304158

2

7.

Seal, Wheel Bearing

304159

2

8.

Jack stand

037708

1

E. CAT C2.2 E

NGINE

S

UPPORT

P

ARTS

G

ROUP

**REFER TO ENGINE MANUAL FOR SPECIFIC PARTS AND SERVICE INFORMATION

PART DESCRIPTION

PART NO.

QTY

****For Most CAT C2.2T Parts, See CAT Manual SEBU8312-02 ****

1.

Hydraulic Pump, CAT C2.2T Engine

306815

1

2.

Hydraulic Pump, CAT C2.2TA Engine

306815

1

«
...
41
42
43
44
45
...
»

Содержание MMP4

































































































Отзывы:

Нет отзывов