Medin medinCNO Скачать руководство пользователя страница 51

Страница: 51 / 68



+49 8142 448 460

[email protected]

www.medin-medical.com

medin Medical Innovations GmbH

Adam-Geisler-Str. 1

D-82140 Olching

OP_medinCNO EN

Rev 12 Stand 06.03.2019

von

8.2

Error messages during operation

Error message text

Colour/

Priority

∆

(1)

Meaning and device response

Disconnection (CPAP, Apnoea

CPAP, SNIPPV mode)

red/
high

<6s

(2)

The CPAP pressure is constantly <2.0 mbar

for >5 seconds - the flow tube or pressure

meter tube are no longer connected to the

medinCNO

. Please reconnect the tube.

This alarm starts the emergency

programme.

Disconnection (oscillation mode)

red/
high

<12s

(2) (3)

The CPAP pressure is constantly <2.0 mbar

for >5 seconds - the flow tube or pressure

meter tube are no longer connected to the

medinCNO

. Please reconnect the tube.

The average value interprets the CPAP

readings from the past five seconds which

delays the start and end of the alarm up to

12 seconds.
This alarm starts the emergency

programme.

CPAP pressure high

red/
high

<1s

CPAP pressure >18 mbar - the medinCNO

briefly interrupts the flow.
This alarm starts the emergency

programme.

Feed pressure high

red/
high

<1s

Feed pressure >40 mbar, the flow supply

tube is blocked or is generating resistance

that is too high. Please check. - The

medinCNO

briefly interrupts the flow.

This alarm starts the emergency

programme.

Device error - patient pressure.

Device must be replaced!

red/
high

<1s

The patient pressure sensor is causing an

error. The two CPAP sensors are measuring

a difference of >2 mbar for 500

milliseconds. The device can no longer be

used and must be replaced. Please contact

a service technician.
This alarm starts the emergency

programme.

Device error - device shut down

necessary

red/
high

<1s

A serious error occurred within the

medinCNO

. The medinCNO

can no longer

be used and must be replaced. Contact a

service technician.
This alarm starts the emergency

programme.

Check gas feed pressure O

red/
high

The O

feed pressure is too low (<3 bar) or

too high (>6.0 bar) - the medinCNO

is only

providing air.
This alarm starts the emergency

programme.

Содержание medinCNO





































































Результаты поиска

Содержание medinCNO

Отзывы:

Бренды по названию

Популярные бренды

Medin medinCNO, Руководство пользователя

Результаты поиска

Содержание medinCNO

Отзывы:

Бренды по названию

Популярные бренды