Medin medinCNO Скачать руководство пользователя страница 50

Страница: 50 / 68



+49 8142 448 460

[email protected]

www.medin-medical.com

medin Medical Innovations GmbH

Adam-Geisler-Str. 1

D-82140 Olching

OP_medinCNO EN

Rev 12 Stand 06.03.2019

von

Alarms and Error Messages

8.1

Error messages during system start-up

Error message text

Meaning

Connect power supply unit - battery low

The internal battery is almost discharged. Please connect

the power supply unit to the mains.

Fan blocked

The fan is blocked, please contact a service technician.

Gas feed pressure low, check O

The oxygen feed pressure is too low (<3 bar). Please

check oxygen feed.

Gas feed pressure high, check O

The oxygen feed pressure is too high (>6 bar). Please

check oxygen feed.

Gas feed pressure low, check air

The air feed pressure is too low (<3 bar). Please check air

feed.

Gas feed pressure high, check air

The air feed pressure is too high (>6 bar). Please check

air feed.

Oxygen calibration failed, check O

The oxygen calibration could not be performed correctly.

Please check whether the oxygen cell is working properly

and whether the medinCNO

is correctly connected to

the oxygen feed. The medinCNO

cannot be operated

without oxygen.

Device error - device shut down necessary

There is a defect in the device’s pneumatic system, at

the overpressure valve or rechargeable battery. The

medinCNO

can no longer be used and must be shut

down. Please contact a service technician.

Error during tube test - restart

An error occurred during the tube test (e.g. leakage).

Please repeat the tube test.

Device error - patient pressure. Device must

be replaced

The patient pressure sensor is causing an error. The

device cannot be used and must be replaced. Please

contact a service technician.

3V battery empty - battery has to be

exchanged.

The internal 3V battery is empty and must be replaced.

Please contact a service technician.

Battery needs replacing - device function in

battery mode cannot be guaranteed. Device

must be connected to mains for use!

The internal rechargeable battery is too old or was used

too frequently and must be replaced. Do not use the

medinCNO

on rechargeable battery power and contact

a service technician.

Maintenance necessary!

Next maintenance necessary:
YY.MM.DD

The last maintenance of the medinCNO

took place at

least 11 months ago and must be repeated no later than

the date indicated. Contact a service technician.

Содержание medinCNO





































































Результаты поиска

Содержание medinCNO

Отзывы:

Похожие инструкции для medinCNO

Бренды по названию

Популярные бренды

Medin medinCNO, Руководство пользователя

Результаты поиска

Содержание medinCNO

Отзывы:

Похожие инструкции для medinCNO

Бренды по названию

Популярные бренды