Medin medinCNO Скачать руководство пользователя страница 48

Страница: 48 / 68



+49 8142 448 460

[email protected]

www.medin-medical.com

medin Medical Innovations GmbH

Adam-Geisler-Str. 1

D-82140 Olching

OP_medinCNO EN

Rev 12 Stand 06.03.2019

von

Accessories

7.1

Accessories

Various accessories and spare parts are available from Medin for operation of the medinCNO

Gas supply tubes

Medin provides gas supply tubes compliant with various

standards.

Water trap

A water trap for the air supply of the medinCNO

can be ordered

together with the medinCNO

. This is then mounted in the air

supply line of the medinCNO

Adapter for patient flow outlet:

Spare adapter, aluminium M22/F15, REF 51091
Spare adapter, white REF 39-902

Spare power supply unit:

REF 39-113

Power plug, EU (without power

supply unit)

REF 39-115

Power plug, UK (without power

supply unit)

REF 39-116

Power plug, USA/Japan (without

power supply unit)

REF 39-117

Power plug, Australia (without

power supply unit)

REF 39-118

Power plug, China (without power

supply unit)

REF 39-127

Spare rechargeable battery

REF 39-101

Spare 3V battery

REF 39-102

Spare oxygen cell

REF MLF–16 or OOM-102

Spare filter for water trap

REF 39-819

Ferrite for RS232 or USB cable

REF 39-125

Filter

REF 39-317

Filter grid

REF 39-318

Retrofit kit

REF 39-320

7.2

Components of the rest of the CPAP system

The medinCNO

must be used in combination with the Medijet

nCPAP generator and the appropriate

accessories (bonnets, masks, prongs and tube circuit sets).

For more specific information on this, visit the homepage

www.medingmbh.com

Warning:

The medinCNO

can only be operated in combination with the Medijet

nCPAP generator and the appropriate

tube circuit sets, bonnets, masks and prongs. If used with any other nCPAP generator, the functionality of the

Содержание medinCNO





































































Результаты поиска

Содержание medinCNO

Отзывы:

Похожие инструкции для medinCNO

Бренды по названию

Популярные бренды

Medin medinCNO, Руководство пользователя

Результаты поиска

Содержание medinCNO

Отзывы:

Похожие инструкции для medinCNO

Бренды по названию

Популярные бренды