Location and Mounting Requirements
Hardware Installation Guide
Mediatrix 4100 – Analog Access Device
9
The cabling is away from the following:
•
Sources of electrical noise such as radios, transmitters, and broadband amplifiers.
•
Power lines and fluorescent lighting fixtures.
•
Water or moisture that could enter the casing of the Mediatrix 4100.
The airflow is not restricted around the Mediatrix 4100 or through the vents of the unit. The unit
requires a minimum of 25 mm (1 in.) clearance.
The fan on the Mediatrix 4100 is not blocked or that the rear of the unit is not too close to the
wall. The unit requires a minimum of 25 mm (1 in.) clearance.
The operating temperature is between 0
o
C and 40
o
C.
The humidity is not over 85% and is non-condensing.
Wiring Requirements
Make sure that the telephone wiring, LAN and WAN cables reach the device and can be dressed in a manner
that is safe for the wiring, does not pull or create lateral stress on the connectors on the device, and does not
present a trip hazard to personnel working in the vicinity of the equipment. Do not connect any cable or wiring
at this time.
Rack-Mounting
The Mediatrix 4100 fits in most standard 48.26 cm (19 in.) racks. Media5 recommends to use a rack compliant
EIA-310-D.
To rack-mount the Mediatrix 4100:
1.
Disconnect all of the cables from the Mediatrix 4100, if applicable.
2.
Insert the Mediatrix 4100 into the rack and secure with suitable screws (not provided). Be sure that
the fan is not obstructed.
To prevent bodily injury when mounting or servicing the Mediatrix 4100 in a rack, ensure that the
rack remains stable. The following guidelines are provided to ensure your safety:
•
Mount the Mediatrix 4100 at the bottom of the rack if it is the only unit in the rack.
•
When mounting the Mediatrix 4100 in a partially filled rack, load the rack from the
bottom to the top with the heaviest component at the bottom of the rack.
•
If the rack is provided with stabilizing devices, install the stabilizers before mounting or
servicing the Mediatrix 4100 in the rack.
3.
Proceed to
“Hardware Installation” on page 10
.
The Mediatrix 4100 has two screw holes on its bottom surface, allowing a single unit to be wall-mounted.
Free Standing Unit
When installing the Mediatrix 4100 on a desk or table, it should be located at least 20 cm from your monitor,
computer casing or other peripherals, including speakers. Never put books or paper on the Mediatrix 4100.
You must also apply the Bumpon
TM
authoadhesive protective products to the bottom of the Mediatrix 4100.
These will stabilize the Mediatrix 4100 and offer skidding resistance.
Condensation
When bringing the unit into a warm environment from the cold, condensation may result that might be harmful
to the unit. If this occurs, allow the unit to acclimatize for an hour before powering it on.
Standards Supported
•
EIA-310-D
•
ETS 300 119
Содержание Mediatrix 4116
