mectron Multipiezo Скачать руководство пользователя страница 40

Страница: 40 / 76

multipiezo

8.3 Cleaning the Tank and Cap

The following procedure must be carried out on the tank and cap of the device.

8.3.1 Preparation

Disconnect the tank from the machine

core unit (see

Chapter 7 on page 28

);

unscrew the cap from the tank.

CAUTION

: Do not sterilise the tank and

cap in an autoclave. They could be damaged.

8.3.2 Required Materials

•

Water;

•

Cleaning solution (pH 6-9);

•

Clean, soft, low-lint cloth;

• Demineralised water.

CAUTION

: To disinfect the device and/

or its accessories, it is recommended the use

of water-based disinfectant solutions with

aneutral pH (pH7).

DO NOT USE

as disinfectants:

•

Alcohol-based disinfectant solutions;

•

Peracetic acid, Formaldehyde,

• Gluteraldehyde based products or other

equivalent solutions/products;

•

very alkaline products (pH > 9);

•

Products containing sodium

hypochlorite;

•

Products containing hydrogen peroxide;

•

Products containing abrasive substances;

•

very acid products (PH < 4);

•

Products containing aldehyde, amine

and/or phenols;

• Acetone;
•

Methylethylketone;

since they may discolour and/or damage the

plastic materials.

The manufacturer disclaims all liability for any

damage caused by the substances mentioned

above. In case of damage caused by those

substances, the Warranty will be void.

8.3.3 Cleaning Method

Thoroughly rinse the inside and outside

of both the tank and cap under running

water;

Содержание Multipiezo












































































Результаты поиска

Содержание Multipiezo

Отзывы:

mectron Multipiezo, Руководство по эксплуатации и обслуживанию, Страница: 40 / 76

Результаты поиска

Содержание Multipiezo

Отзывы: