mectron Multipiezo Скачать руководство пользователя страница 13

Страница: 13 / 76

IDENTIFICATION DATA

Symbol

Description

Symbol

Description

QTY.1

Quantity in package: 1

Rx only

For uS market only

CAUTION

: U.S. Federal

law restricts this device

to sale by or on the

order of a licensed

dentist or dental

hygienist.

Table 1 –

Symbols

a) The symbol is represented by a yellow triangle and

black graphic symbol.

NOTE:

For other symbols, refer to

Chapter

12.1 on page 61

IDENTIFICATION DATA

A correct description of the model and of

the serial number of the device will allow the

After Sales Service to provide fast and efficient

support.

Always provide this information every time

that you contact Piezosurgery Inc.’s Service.

2.1

Identification Plate of the Device

Each device is equipped with an

identification plate indicating the main

technical characteristics and serial

number. The identification plate is located

on the bottom of the device’s console.

The complete technical specifications are

provided in

Chapter 11 on page 52

NOTE:

The complete list of symbols is

provided in

Chapter 1.5 on page 6.

manufacturer

Mectron S.p.A.

Via Loreto 15/A

16042 Carasco -GE- Italy

106000000

multipiezo

100-240 V

90 VA - 50/60 Hz.

Rx Only

0051

00000000

YYYY-MM-DD

made in Italy

Bar Code HIBC 128

Additional symbols and characteristics

of the device are provided on a separate

plate. This identification plate is located

on the bottom of the device’s console.

NOTE:

The complete list of symbols is

provided in

Chapter 1.5 on page 6.

multipiezo

Device for intermittent operation:

55 s ON - 30 s OFF with irrigation

30 s ON - 120 s OFF without irrigation

Содержание Multipiezo












































































Результаты поиска

Содержание Multipiezo

Отзывы:

mectron Multipiezo, Руководство по эксплуатации и обслуживанию, Страница: 13 / 76

Результаты поиска

Содержание Multipiezo

Отзывы: