STEP 6. Hinge Assembly - Left Side of Grill
Align the hole in the Long Hinge (18) with the front side hole
inside the Bowl (4). Insert a 10-24 x 1/2” Bolt (22) through the
Long Hinge and Bowl
(FIG. 6)
. Attach a Square Nut (20) from
the inside of the Bowl and tighten.
Repeat for the Short Hinge (17) at the rear side hole in the
Bowl.
Note:
Tighten Bolts and Square Nuts, but make sure Hinges
move easily.
STEP 7. Hinge Assembly - Right Side of Grill
Repeat STEP 6 for the opposite side of the Bowl, to attach the
other Long Hinge (18) and Short Hinge (17).
(FIG. 6)
.
Note:
Tighten Bolts and Square Nuts, but make sure Hinges
move easily.
FIG. 6
Long Hinge
Short Hinge
1/2” Bolt
Square Nut
STEP 8. Bowl / Leg Assembly
(FIG. 7)
With the Bowl (4) on its side, put a 1-1/4” Bolt (23)
through the rear center hole of the Bowl and center hole of the
Wheel Leg (3). Attach a Square Nut (20) loosely and repeat for
other two Bolts and Square Nuts in the Bowl and Wheel Leg.
Tighten all three Bolts and Square Nuts.
Repeat for the Front Leg (2).
Note:
Square Nuts should be under grill, and tightened
completely after Legs are assembled to Bowl.
FIG. 7
FIG. 8
STEP 9. Hood / Bowl Assembly
(FIG. 8)
With the grill assembly still on its side, lean the Hood (5) on its side
and the back of the Hood against the back of the Bowl (4). Beginning at the
top, swing the hinges from the Bowl to inside the Hood. Align the upper hole
in the Hood (the hole closest to the back) with the Short Hinge (17) and the
bottom hole with the Long Hinge (18). Insert a 10-24x1/2” Bolt (22) through
the Hood and Hinges. Attach a Square Nut (20) from the inside of the Hood
to each Bolt and tighten.
Repeat for the Short and Long Hinge at the opposite side.
Note:
Tighten Bolts and Square Nuts, but make sure Hinges and Hood
move easily.
FIG. 9
STEP 10. Hood Handle and Round Vent
(FIG. 9)
Insert a 10-16 x 5/8” Screw (19) through the Hood (5), to hole in
Hood Handle (8). Do not tighten completely. Repeat for other Screw and
Hood Handle hole. Tighten both Screws securely in Handle.
Put the Round Vent (12) over the slots in the top of the Hood so the small
tab on the Round Vent is in the slot with the notch. Place a 1/2” Bolt (22)
through the vent and Hood and attach a Square Nut (20). Tighten Bolt and
Square Nut, but make sure the Round Vent can rotate easily.
TIP:
For STEPS 8, 9, and 10, lay the grill and parts down
on its side, onto a clean, flat surface, for easy assembly.
Set the grill upright in the normal position.
STEP 11. Insert Ash Pan (24)
STEP 12. Insert Cooking Grid (25)
Install Cooking Grid on the grid brackets so the small wires run front to back,
and are on top.
5
FIG. 10
YOU ARE NOW READY TO USE YOUR GRILL.
BUT FIRST READ AND UNDERSTAND
WARNINGS AND OPERATIONAL INSTRUCTIONS
.
Wheel Leg
Front Leg
1-1/4” Bolt
Square Nut
Square
Nut
1/2” Bolt
Hood Handle
5/8” Screw
Round
Vent
1/2” Bolt
Square
Nut
Bowl Handle
