manualshive.com logo in svg

Mec Micro 13-XD, Руководство по обслуживанию и запасным частям

Поделиться
Скачать
Mec Micro 13-XD Скачать руководство пользователя страница 21

Page 17

Mcro 19-XD - Servce & Parts Manual

June 2020

Secton 10 - Mantenance

Frequent Inspection Checklist

THIS CHECKLIST MUST BE USED AT 3-MONTH INTERVALS OR EVERY 
150 HOURS OF MACHINE USE, WHICHEVER OCCURS FIRST������ FAILURE 
TO DO SO COULD RESULT IN DEATH OR SERIOUS INJURY������

Frequent Maintenance Inspections should be conducted by qualified service technicians only. 
Photocopy the Frequent Inspection Checklist page from the Operator’s Manual to keep record of 
this inspection. Keep inspections records up to date. Record and report all discrepancies to your 
supervisor.

Perform all checks listed on Pre-Start Inspection, then proceed with the following checks.

Hydraulic Fluid

Inspect the condition of hydraulic fluid in the reservoir. Oil should be a clear and amber in color.

Batteries

Proper battery condition is essential to good machine performance and operational safety. Improper 
or damaged cables and connections can result in component damage and hazardous conditions.

ELECTROCUTION / BURN HAZARD������ CONTACT WITH ELECTRICALLY 
CHARGED CIRCUITS COULD RESULT IN DEATH OR SERIOUS INJURY������ 

REMOVE ALL RINGS, WATCHES AND OTHER JEWELRY������

BODILY INJURY HAZARD������ BATTERIES CONTAIN ACID������ AVOID SPILLING 
OR CONTACTING BATTERY ACID������ NEUTRALIZE BATTERY ACID SPILLS 
WITH BAKING SODA AND WATER������

Put on protective clothing and eye wear.
Slide out the component tray from the chassis.
Be sure that the battery cable connections are free of corrosion.

NOTE: Adding terminal protectors and a corrosion preventative sealant will help eliminate 

corrosion on the battery terminals and cables������

Be sure that the battery retainers and cable connections 
are tight.
Fully charge the batteries. Allow the batteries to rest 
24 hours before performing this procedure to allow the 
battery cells to equalize.
Check each battery pack and verify that the batteries are 
wired correctly.
Inspect the battery charger plug and pigtail for damage 
or excessive insulation wear. Replace as required.

4.

5.

6.

7.

ART_5050

Batteries

Power 

Switch

150A Fuse

Battery

Charger

1.
2.
3.

Содержание Micro 13-XD

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды