background image

Page 10

3084ES Speed Level

TM

 - Operator’s Manual

August 2020

Secton 4 - Hazards

Fall Hazards & Collision Hazards

Fall Hazards

ART_3067

DO NOT CLIMB ON 

RAILS

DO NOT sit, stand or climb on the platform guard rails. Maintain a firm footing 
on the platform floor at all times.

DO NOT exit the platform when elevated

DO NOT climb down from the platform when elevated.

Keep the platform floor clear of debris.

DO NOT fasten a fall restraint lanyard to an adjacent structure.

Ensure that the entry is properly closed before operating the machine.

Operators must comply with employer, job site and governmental rules 
regarding the use of personal protective equipment.

ART_3058

DO NOT EXIT 

PLATFORM WHEN 

ELEVATED

Collision Hazards

ART_3072

ART_3062

ART_3066

Be aware of blind spots while operating this machine.

Watch for overhead obstructions when elevating the platform.

Watch for crushing hazards when holding the platform rail.

Reduce travel speed when moving the machine on slopes, when near 
personnel and obstacles, or when surface conditions are wet, slippery or 
otherwise limiting.

DO NOT operate in the path of any crane unless the controls of the crane have 
been locked out and/or precautions have been taken to prevent any possible 
collision.

Stunt driving and horseplay are PROHIBITED.

Содержание 3084ES

























































Отзывы: