MDT Technologies SCN-IP000.03 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 57

background image

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

8

8

2.6 Commissioning with Data Secure

The following procedure is recommended for commissioning the SCN-IP100.03:

1.

Insert the application „SCN-IP100.03 – KNX IP Router with Secure“

2.

Input of the FDSK (see sticker on the side of the device)

3.

Configuration of the IP Router.

4.

Transfer of the physical address and the application of the IP Router. For this, the
programming button has to be

pressed shortly

. The programming

LED lights steadily red

.

5.

After successful transfer of the physical address and the application, the red LED turns off
again.

6.

Insert the application „SCN-IP000.03 – KNX IP Router with email function“

7.

Input of the FDSK (see sticker on the side of the device)

8.

Configuration of the E-Mail Client.

9.

Transfer of the physical address and the application of the E-Mail Client. For this, the
programming button has to be

pressed long

. The programming

LED flashes red

.

10.

After successful transfer of the physical address and the application, the red LED turns off
again.

11.

Accessing the Web client to configure the e-mail addresses by opening an Internet browser
and call the address: http:\\IP address: port, for example: http: \\192.168.1.178:8080 for the
IP address 192.168 .1.178 and the http port 8080

FDSK Info:

The IP Router has two FDSK (Factory Default Setup Key), one for each application.

Therefore you will find two different keys on the right and left side of the interface.

Important

: By deactivating "Secure commissioning" in the properties -> settings of the device, the

device is operated "unsecure", i.e. in "plain mode". If you are prompted to enter the FDSK of the
device, you can skip this dialog by clicking the "Later" button. Data Secure/IP Secure can also be
activated later by activating "Secure commissioning" and the FDSK is present.
Further details about IP Secure/Data Secure can be found at “3 Safety – IP Secure/Data Secure”

«
...
6
7
8
9
10
...
»

Содержание SCN-IP000.03


























































Отзывы:

Нет отзывов

Похожие инструкции для SCN-IP000.03

Бренд: Garland Страницы: 4

Бренд: LaCie Страницы: 4

Бренд: LaCie Страницы: 4

Бренд: LaCie Страницы: 4

Бренд: Draytek Страницы: 8

PoleVault System A/V Source Inputs

Бренд: Extron electronics Страницы: 4

Бренд: 3Com Страницы: 50

Enterasys Matrix 2G4082-25

Бренд: Enterasys Страницы: 58

Ethernet MCA 10/100 Adapter

Бренд: Olicom Страницы: 88

HiGain H4TU-R-402 List 5A

Бренд: ADC Страницы: 7

Бренд: Matrix Switch Corporation Страницы: 48

ExtremeCloud Appliance E1120

Бренд: Extreme Networks Страницы: 219

Бренд: Divio Страницы: 78

Бренд: Costar Страницы: 24

Бренд: Axis Страницы: 10

Бренд: Magnescale Страницы: 73

Zum ZUMMESH-NETBRIDGE

Бренд: Crestron Страницы: 2

Бренд: Icom Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды