MDT Technologies SCN-IP000.03 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 57

background image

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

31

31

Telegram confirmations on
line



if routed



always

Defining whether the router should
send an Acknowledge

Send confirmation on own
telegrams



yes



no

Defining whether the router should
send an Acknowledge

Configuration from sub line



enable



disable

Defining whether it can be
programmed by TP side

Table 7: Settings – Sub line

If the "configure" parameter is active for the "Configuration", the following parameters are freely
adjustable.
For all other "Configuration" the parameters are set to fixed values - according to the setting.

The effects of the individual settings for the relevant parameters are described in detail below:

Group telegrams:



block

No group telegrams of the respective main groups are routed to KNX/EIB.



transmit all

All group telegrams of the respective main group are routed independently of the filter table
to KNX/EIB.



filter

Here is checked with the help of the filter table, whether the received group telegram will be
routed to KNX/EIB. The filter table is automatically generated by the ETS.

Configuration from sub line:

This parameter can be used to suppress programming from the TP/KNX side, thus achieving a higher
level of safety.

«
...
29
30
31
32
33
...
»

Содержание SCN-IP000.03


























































Отзывы:

Нет отзывов

Похожие инструкции для SCN-IP000.03

3CR860-95 - OfficeConnect Secure Router

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 26

Бренд: Rain Bird Страницы: 17

Бренд: Nayar Systems Страницы: 37

Бренд: Lab.gruppen Страницы: 35

Бренд: Watchguard Страницы: 24

Бренд: H3C Страницы: 400

Бренд: XNET Страницы: 17

Marconi OMS 1200

Бренд: Ericsson Страницы: 136

Бренд: Kontron Страницы: 42

AyrMesh IndoorAP

Бренд: AYRSTONE Страницы: 2

Бренд: Xenya Страницы: 189

Бренд: B+B SmartWorx Страницы: 52

Бренд: Moxa Technologies Страницы: 36

BROADCAST POLLING FRAD BPF-14 BU

Бренд: DCB Страницы: 28

AceroDURO 100/S100

Бренд: CNC-Step Страницы: 86

Бренд: FiberHome Страницы: 2

Бренд: Wave Wireless Networking Страницы: 167

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды