MDT Technologies SCN-IP000.03 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 57

background image

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

23

23

4.1.3 Device – IP Configuration

The following picture shows the IP settings of the unit:

Figure 12: Device – IP Settings

Obtain an IP address automatically

The unit obtains the address automatically. A DHCP server needs to be available.

Use a static IP address

The user specifies a fixed IP address.

Subnet Mask/Standard Gateway

This can only be set with the setting "Use a static IP address".
The netmask is used by the unit to determine whether a communication partner is in the local
network. If a partner is not in the local network, the unit does not send the telegrams directly to the
partner, but to the gateway, which takes over the forwarding.
The setting of the gateway makes it possible for networks based on different protocols to
communicate with each other.
Note: If the KNX IP Router is only to be used in the local LAN, the entry 0.0.0.0 can remain.
The network settings of the communicating PC can be read in the network settings of the PC.

«
...
21
22
23
24
25
...
»

Содержание SCN-IP000.03


























































Отзывы:

Нет отзывов

Похожие инструкции для SCN-IP000.03

Бренд: E-Lins Страницы: 59

Бренд: E-Lins Страницы: 11

Бренд: E-Lins Страницы: 9

Бренд: E-Lins Страницы: 5

Network Video Recorders

Бренд: e-Line Technology Страницы: 34

Бренд: LaCie Страницы: 4

Бренд: LaCie Страницы: 4

Бренд: LaCie Страницы: 4

grandMA2 Series

Бренд: MA lighting Страницы: 36

Бренд: National Instruments Страницы: 162

Бренд: ZyXEL Communications Страницы: 299

Бренд: Matrix Switch Corporation Страницы: 60

Бренд: TRENDnet Страницы: 7

ACC-BKT-AX-BEAM

Бренд: Extreme Networks Страницы: 35

Бренд: AIC Страницы: 79

RouteFinder RF560VPN

Бренд: Multitech Страницы: 82

Бренд: NETGEAR Страницы: 3

Бренд: Allied Telesis Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды