MD Helicopters CSP-900RMM-2, Техническое обслуживание и ремонт

Страница: 639 / 2144

CSP − 900RMM − 2 MD Helicopters, Inc.
Rotorcraft Maintenance Manual
Page 207
Revision 25
25-60-10
Legend (Ref. Figure 4)
1. FLOAT GUARD
2. COVER
3. FLOAT BAG
4. VELCRO (HOOK)
5. VELCRO (PILE)
6. STRAP
7. FLOAT BAG SUPPORT
8. SUPPORT RAIL
9. SKID GUARD
10. CLAMP
11. DECAL
C. Assist Handle Removal
(Ref. Figure 1)
(1). Remove bolt (40), washers (39), and nut
(38) securing aft clamp (42) to handle
(43).
(2). Remove bolts (37), washers (39), and
nuts (38) securing aft clamp (42) to
support tube (4). Remove aft clamp.
(3). Remove bolt (40), washers (39), and nut
(38) securing forward clamp (41) to
handle (43). Remove handle.
(4). Remove bolts (37), washers (39), and
nuts (38) securing forward clamp (41) to
support tube (4). Remove forward
clamp.
D. Fairing Removal
(Ref. Figure 2)
(1). Remove screws (8) and washers (9) and
remove end cap assembly (11) from
upper and lower fairings (1 and 10).
(2). Remove screws (8) and washers (9) and
remove lower fairing (10) from support
assemblies (2 and 3), clip assemblies (4,
5, 6 and 7) and upper fairing (1).
(3). Remove screws (8) and washers (9) and
remove upper fairing (1) to support
assemblies (2 and 3) and clip assem­
blies (4, 5, 6 and 7).
E. Hoist Removal
(Ref. Figure 1)
(1). Remove power from aircraft (Ref.
Section 96-00-00)
(2). Detach connectors P524, P525 and
P526 from aircraft connectors J524,
J525, and J536. (Ref CSP-900RMM-3,
98-30-00)
(3). Detach harness connector P8 from hoist
assembly (22) and connector P2 from
controller assembly (16).
(4). Remove bolt (27), washer (25) and lock
nut (26) and detach upper end of strut
assembly (23) from lower attach point
of aft bracket assembly (2).
Ensure no load is attached to
hoist without strut assembly
(23) in position and secured at upper and
lower points.
(5). Remove washers (18) quick release pins
(29) and bushings (28) into support
tube (4). Slide support tube (4) off
fitting assemblies (35) and (36).
NOTE:
If hoist is to be removed from support
tube (4), proceed with steps 6 through 10.
(6). Remove bolts (20), washers (7) and lock
nuts (21). Detach hoist assembly (22)
from lower attach points of bracket
assemblies (1 and 2).
(7). Remove with bolts (17), washers (18)
and lock nuts (19). Detach hoist
assembly (22) from upper attach points
of bracket assemblies (1 and 2).
(8). Remove lockwire. Remove bolts (15)
and washers (7). Detach controller
assembly (16) from control box support
(11)
(9). Remove bolts (14) and washers (13).
Detach support assemblies (9 and 10)
and control box support (11) from
bracket assemblies (1 and 2).
(10). Remove bolts (12) and washers (13).
Detach support assemblies (9 and 10)
from control box support assembly (11)
F. Skid Guard Removal
(Ref. Figure 3)
(1). Remove fillet seal around all clamps (4).
CAUTION