McQuay ACZ 010A Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 48

McQuay ACZ 010A Скачать руководство пользователя страница 37

IOMM ACZ1

ACZ 010A through 039A

37

Screen Definitions – ALARM

ALARM ACTIVE (X)
Alarm Description
hh:mm:ss dd/mmm/yyyy

OR

ALARM ACTIVE (X)
No more alarms
Press ENTER to clear
all active alarms

If the unit is off on a shutdown alarm or running but in a limit alarm condition, the cause and date will
appear in the upper screen. If there is a simultaneous occurrence of more than one alarm, the others
will appear in additional screens below this one, accessed by the DOWN ARROW. Either type alarm
will light a red light in back of the LEFT-KEY. The light will go out when the fault is cleared.

To clear the fault, scroll down to the last screen and press ENTER. If other faults have appeared, they
will all be cleared at the same time.

ALARM LOG (1)
High Condenser Press
hh:mm:ss d/mmm/yyyy

The last 25 alarms, either shutdown or limit, are shown in this menu with subsequent menus stored
under it. ARROW DOWN from this menu will go to the next-to-last alarm, ARROW DOWN again
will go to the second from last, and so on through the last 25 occurrences. The screens are numbered
(1), (2), (3), etc.

Screen Definitions – SET

Changing setpoints

; in general, setpoints are changed as follows:

1.

Select the desired menu by scrolling through SET menus with the UP and DOWN ARROWS.

2.

When the desired menu is selected, select the desired entry by moving between lines using the
ENTER key.

3.

If a numerical value is being changed, use the INCREMENT key (UP ARROW) to increase or
the DECREMENT key (DOWN ARROW) to decrease the value of the setpoint.

If a word type setpoint (for example, YES or NO) is to be selected, the choices are loaded into
the menu and selected by scrolling through the available setpoint options using the UP ARROW
key.

4.

Enter the desired value or word into the controller by pressing the SET key.

«
...
35
36
37
38
39
...
»

Содержание ACZ 010A

















































Отзывы:

Нет отзывов