McNeilus HD Rear Loader Скачать руководство пользователя страница 87

Страница: 87 / 132

Rear Loader

Operation

4.7.3

Daily Inspection

•  Inspect tank daily for damage or leaks.
•  Replace (do not repair) damaged or leaking tank.
•  Drain pressure before driving.
•  Do not weld or repair tank.
•  Never exceed stated PSI in tank.
•  Bursting tank may injure or kill.

4.7.3.1

Tank Integrity

At the start of each shift:

•

Inspect Interior:

Drain the tank of water and use a

flashlight to look into the tank through the fill opening.

Look for signs of corrosion on the inside of the tank which

may indicate that the tank has been weakened and is in

need of replacement.

•

Inspect Exterior without Pressure:

If the interior

inspection indicates that the tank is in good condition, fill

the tank with water and inspect the exterior of the tank

thoroughly for signs of leaks. Inspect the filler neck and fill

opening. Look for signs of damage. Look for cracks in the

weld joints or seams. Check that all fastening hardware is

tight and undamaged. Inspect fittings for signs of damage,

cracks, or looseness.

•

Inspect Exterior with Pressure:

If there are no signs

of damage or exterior leakage, pressurize the tank and

repeat the inspection.

•

Depressurize Tank:

Release the pressure in the tank as

soon as you are finished inspecting and before moving

the truck.

Replace Defective Tank:

Water tanks with any leak or

significant signs of internal or external damage or corrosion

should be replaced. DO NOT ATTEMPT TO REPAIR.

4.7.3.2

Pressure Regulator Valve

•

Inspect Pressure Regulator:

The pressure regulator

is used to reduce the air brake system pressure to a

pressure that is safe to be used in the water tank. It

must be undamaged and in proper working order. Look

and listen for signs of leaking. Ensure that the valve and

associated hoses and fittings are undamaged.

•

Adjust Pressure to Correct Setting:

Many pressure

regulators are set at the factory and cannot be adjusted.

If your water tank has an adjustable regulator, set it to 50

psi. When setting the regulator, always begin by turning

the adjusting knob counterclockwise first to reduce the

pressure slightly. Then turn it clockwise slowly to bring the

pressure up to the correct setting. Never continue to turn

the valve past the correct setting.

•

Replace Defective Regulator Valve:

Any water tank with

a damaged or missing pressure regulator valve must be

removed from service immediately. Do not pressurize the

tank until a functioning pressure regulator valve has been

installed.

Содержание HD Rear Loader





































































































































Результаты поиска

Содержание HD Rear Loader

Отзывы:

Бренды по названию

Популярные бренды

McNeilus HD Rear Loader, Руководство оператора

Результаты поиска

Содержание HD Rear Loader

Отзывы:

Бренды по названию

Популярные бренды