McNeilus HD Rear Loader страница 88 Скачать руководство пользователя

Страница: 88 / 132

Rear Loader

4.7.3.3

Pressure Relief Valve

•

Inspect the Relief Valve:

The pressure relief valve is a

safety device that will release air or water from the tank if

it is inadvertently pressurized over the relief setting. The

relief setting on most water tanks is set at the factory and

cannot be adjusted. Identify the pressure relief valve and

ensure that it has not been damaged or tampered with.

•

Replace Defective Relief Valve:

Any water tank with

a damaged or missing pressure relief valve must be

removed from service immediately. Do not pressurize the

tank until a functioning pressure relief valve has been

installed.

4.7.4

Daily Operation

The water tank is designed to be used during stationary

operation at the yard or the landfill site only. Do NOT

pressurize the tank while driving. A pressurized water tank is

an added hazard in the event of a crash or a rollover.

4.7.5

Vehicle Handling Characteristics

Safe operation of any vehicle is the responsibility of the driver.

The water tank is a fluid load that can increase the rollover

tendency if the truck is driven with the water tank partially

full. To reduce the risk of rollover, only drive the truck with the

water tank either completely full or completely empty. Avoid

making sharp turns at excessive speeds and other abrupt

maneuvers.

Operation

In the event of a rollover or crash, an unbelted person is

significantly more likely to become injured or die than a person

wearing a seat belt. ALWAYS WEAR YOUR SEAT BELT.

4.7.6

Water Tank Sign Identification

Item Part Number

Qty.

Comments

1449162

Use if equipped with 55 PSI tank.

1449165

Use if equipped with 95 PSI tank.

1503949

Use if equipped with 120 PSI tank.

1449164

Use on all tanks.

(Side Tank Mount)

Содержание HD Rear Loader





































































































































Результаты поиска

Содержание HD Rear Loader

Отзывы:

Похожие инструкции для HD Rear Loader

Бренды по названию

Популярные бренды

McNeilus HD Rear Loader, Руководство оператора

Результаты поиска

Содержание HD Rear Loader

Отзывы:

Похожие инструкции для HD Rear Loader

Бренды по названию

Популярные бренды