McElroy Hornet XL ASW31401 Скачать руководство пользователя | Manualshive

Страница: 30 / 34

background image

Maintenance

7 - 1

Maintenance

Hornet™ XL

MAINTENANCE

Preventative Maintenance

To insure optimum performance, the machine must be kept
clean and well maintained.
With reasonable care, this machine will give years of service.
Therefore, it is important that a regular schedule of preventive
maintenance be kept.
Store machine inside, out of the weather, whenever possible.

Clean Machine

1)

Clean the machine with soap and water as needed.

Do not pressure wash.

Check Machine Operation

1)

Open and close the carriage of the machine. If the

machine has resistance opening or closing, inspect the
carriage guide rods for debris in the rack and brush
any debris out of the rack.

2)

Inspect the gearboxes and cross shaft for damage.

Ensure power is being transmitted from gearbox to
gearbox with a minimal amount of free play in the
handle.

3)

Engage the carriage brake and orient the machine

vertically. Apply pressure on the carriage with hands. If
the brake slips and doesn't hold the carriage position,
replace the brake.

4)

Inspect the jaw clamps for proper operation. Replace

any damaged jaw clamps.

5)

Inspect chain clamps for proper operation. Replace

any damaged chain clamps.

Fasteners Are Tight

1)

Inspect all machine fasteners for tightness. Tighten any

loose fasteners.

Changing Heater Plates/

Adapters

The heater body of this assembly is not coated. Coated heater
plates/adapters are available for all fusion applications.
Heater plates/adapters are installed with stainless steel cap
screws.
Care should be taken to assure that the heater adapters are
seated on the heater body, and that there is no foreign matter
trapped between these surfaces.

IMPORTANT:

Do not over-tighten the bolts.

The surface of the heater adapters are coated with an anti-
stick coating.

NOTICE:

Only install heater adapters when the heater is

cool.

Task

As Needed

Daily

Monthly

Yearly

Clean Machine

l

Check Machine Operation

l

Fasteners Are Tight

l

Changing Heater Plates/Adapters

l

Clean Chains

l

Clean Fitting and Drill Adapter

l

Adjust Gearbox Chain Tension

l

CD02479-03-15-19

«
...
28
29
30
31
32
...
»

Содержание Hornet XL ASW31401



































Отзывы:

Нет отзывов

Похожие инструкции для Hornet XL ASW31401

Бренд: ACS Страницы: 56

Бренд: Parata Страницы: 40

Бренд: EASTERN INSTRUMENTS Страницы: 93

Бренд: Pari Страницы: 2

Бренд: Hakko Electronics Страницы: 8

Professional HS 8

Бренд: Hailo Страницы: 5

Бренд: Hainbuch Страницы: 52

Бренд: Halyard Страницы: 88

Бренд: HALDER Страницы: 2

Бренд: Hällde Страницы: 40

Бренд: Hällde Страницы: 6

Synthesis SDEC-3000

Бренд: JBL Страницы: 24

Бренд: Xilica Audio Design Страницы: 30

Бренд: Kellfri Страницы: 12

Бренд: R&S Страницы: 371

Бренд: R.M. Young Страницы: 9

Бренд: Teac Страницы: 76

Бренд: Teac Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды