McCrometer FlowConnect Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 19

background image

Copyright © 2016 McCrometer, Inc. All printed material should not be changed or altered without permission of McCrometer. Any

published technical data and instructions are subject to change without notice. Contact your McCrometer representative for current

technical data and instructions.

www.mccrometer.com

3255 WEST STETSON AVENUE • HEMET, CALIFORNIA 92545 USA

TEL: 951-652-6811 • 800-220-2279 • FAX: 951-652-3078 Printed In The U.S.A. Lit. # 30122-40 Rev. 1.0 / 3-1-17

Page 4 of 19

™

FlowConnect

!

WARNING!

Never remove a meter or top plate assembly while the line is under pressure!

STEP 4: Remove the flow meter from the pipe
Remove the flow meter from the pipe as described in Section 3.0 of the Installation, Operation, and Maintenance (IOM)

manual for Mc Propeller Flow meters.

STEP 5: Remove the mechanical unit and base plate
a. Remove the six screws around the base.

b. Lift up and remove the canopy.

c. Loosen the pal nut (10019-00) from the base plate.

d. Unscrew and remove the register. Set it aside to be used

later.

e. Unscrew and remove the pal nut (10019-00) from

register. You will no longer need the pal nut and can

discard it.

f. Unscrew and remove the brass bushing (R0142-00)

from the base plate.

g. Lift up and remove the base plate from ell bracket.

b

x6

a

d

c

e

f

g

«
...
2
3
4
5
6
...
»

Содержание FlowConnect




















Отзывы:

Нет отзывов

Похожие инструкции для FlowConnect

LevelMaster 7100

Бренд: ABB Страницы: 2

Бренд: ABB Страницы: 4

Бренд: Kawai Страницы: 33

Бренд: Kawai Страницы: 60

Бренд: janitza Страницы: 6

Бренд: janitza Страницы: 36

Бренд: Velleman Страницы: 96

Бренд: Dewetron Страницы: 24

Бренд: ADA INSTRUMENTS Страницы: 27

Fusion-L 6 digit

Бренд: London Electronics Страницы: 44

Бренд: RaySafe Страницы: 2

Бренд: A&D Страницы: 2

Бренд: Hammond Страницы: 106

Бренд: Konica Minolta Страницы: 48

Бренд: VECTECH Страницы: 10

Бренд: Gatekeeper Страницы: 2

Бренд: Midtronics Страницы: 58

Бренд: Niigata seiki Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды