McCrometer FlowConnect Скачать руководство пользователя страница 14

Страница: 14 / 19

published technical data and instructions are subject to change without notice. Contact your McCrometer representative for current

technical data and instructions.

www.mccrometer.com

3255 WEST STETSON AVENUE • HEMET, CALIFORNIA 92545 USA

TEL: 951-652-6811 • 800-220-2279 • FAX: 951-652-3078 Printed In The U.S.A. Lit. # 30122-40 Rev. 1.0 / 3-1-17

Page 14 of 19

™

FlowConnect

1: Power connector

For models with rechargeable batteries, a solar panel can be connected through the Power connector at the top of the

connector plate.

2: Inputs connector

The FlowConnect unit supports up to two analog inputs through the Inputs connector. Inputs are most often sensors, such

as a rain gauge or a pressure sensor. The Inputs connector will either be in the middle or at the bottom of the connector

plate.

For simple configurations with just one sensor, plug the sensor directly into the Inputs port. To connect more than one

sensor to the Inputs port, a Y-Cable (200.720.510) is needed. No more than two sensors can be connected at once, so only

one Y-Cable is required.

3: Outputs connector

The Outputs connector is only available on FlowConnect models with a digital register. It provides 4-20mA and pulse

output options. To enable the FlowConnect to send a 4-20mA or pulse output to another system, such as a SCADA system,
an output cable (5M-025-OE) is required. If you choose to use this option, use the table below as a guide for wire colors:

Output Cable Wire Color:

Grey

Green

Brown

Yellow

White

Open Collector Pulse Only

Pulse (-)

Pulse (+)

Optically Isolated Pulse and 4-20mA 4-20mA (+) 4-20mA (-)

Pulse (-)

Pulse (+)

Relay Pulse and 4-20mA

4-20mA (+) 4-20mA (-)

Normally Closed

Common

Normally Open

Содержание FlowConnect




















Результаты поиска

Содержание FlowConnect

Отзывы:

Бренды по названию

Популярные бренды

McCrometer FlowConnect, Инструкция по модернизации

Результаты поиска

Содержание FlowConnect

Отзывы:

Бренды по названию

Популярные бренды