MBW F36/4, Руководство по безопасности и обслуживанию оператора

Страница: 12 / 29

- 9 -
S
ERVICE
Assembly and disassembly should be performed by a
service technician who has been factory trained on MBW
equipment. The unit should be clean and free of debris.
Pressure washing before disassembly is recommended.
• Prior to assembly, wash all parts in a suitable cleaner or
solvent.
• Check moving parts for wear and failure. Refer to the
Replacement section in this manual for tolerance and
replacement cycles.
• All shafts and housings should be oiled prior to pressing
bearings. Also, ensure that the bearings are pressed
square and are seated properly.
• All bearings, seals, o-rings and gaskets should be
replaced when rebuilding gearbox.
Torque Chart
Service Tools
Gearbox Disassembly
Refer to Gearbox Assembly, page 14.
1. Remove the handle, belt guard & drive assembly
(page 18), engine & guard ring (page 20).
2. Loosen the square head set screw (page 16, #20)
until the gearbox housing can be lifted off the spider
assembly.
3. Flip the gearbox housing (#7) over and set it on the
four guard ring pads.
4. Remove the yoke arm (#9) by removing one of the
retaining rings (#6), holding the pivot rod (#12) and
sliding the rod out of the holes.
5. Remove the two flange bolts (#24) and the two flat
head screws (#25) that hold the cover (#8) to the
gearbox housing (#7).
6. Remove the cover and discard the shims (#11) and
the o-ring (#5).
7. Pull out the shaft (#14) with the bearings (#3) and the
worm gear (#13) and drain oil out of gearbox.
8. Press bearing (#3) and worm gear (#13) off long side
of shaft (#14).
9. Remove key (#15) and retaining ring (#2) from shaft.
10. Press remaining bearing (#3) off of shaft.
11. Remove the four flange bolts (#23) and the bearing
cap (#20). Discard the shim gasket (#10) and the
o-ring (#17).
12. Remove the worm shaft (#19) and the bearings (#22).
13. Remove the retaining cap (#21) and discard the shim
gasket (#10) and the o-ring (#17).
Gearbox Assembly
Refer to Gearbox Assembly, page 14.
1. Lightly oil the shaft (#14). Install the key (#15) and
the retaining ring (#2) onto the shaft.
2. With the retaining ring end of the shaft down, press
the worm gear (#13) onto the shaft. Make sure the
SIZE GRADE 2 GRADE 5 GRADE 8
1/4-20 49 in
•
lbs 76 in
•
lbs 9 ft
•
lbs
1/4-28 56 in
•
lbs 87 in
•
lbs 10 ft
•
lbs
5/16-18 8 ft
•
lbs 13 ft
•
lbs 18 ft
•
lbs
5/16-24 9 ft
•
lbs 14 ft
•
lbs 20 ft
•
lbs
3/8-16 15 ft
•
lbs 23 ft
•
lbs 33 ft
•
lbs
3/8-24 17 ft
•
lbs 26 ft
•
lbs 37 ft
•
lbs
7/16-14 24 ft
•
lbs 37 ft
•
lbs 52 ft
•
lbs
7/16-20 27 ft
•
lbs 41 ft
•
lbs 58 ft
•
lbs
1/2-13 37 ft
•
lbs 57 ft
•
lbs 80 ft
•
lbs
1/2-20 41 ft
•
lbs 64 ft
•
lbs 90 ft
•
lbs
9/16-12 53 ft
•
lbs 82 ft
•
lbs 115 ft
•
lbs
5/8-11 73 ft
•
lbs 112 ft
•
lbs 159 ft
•
lbs
5/8-18 83 ft
•
lbs 112 ft
•
lbs 180 ft
•
lbs
3/4-16 144 ft
•
lbs 200 ft
•
lbs 315 ft
•
lbs
1-8 188 ft
•
lbs 483 ft
•
lbs 682 ft
•
lbs
1-14 210 ft
•
lbs 541 ft
•
lbs 764 ft
•
lbs
1-1/2-6 652 ft
•
lbs 1462 ft
•
lbs 2371 ft
•
lbs
M 6 3 ft
•
lbs 4 ft
•
lbs 7 ft
•
lbs
M 8 6 ft
•
lbs 10 ft
•
lbs 18 ft
•
lbs
M 10 10 ft
•
lbs 20 ft
•
lbs 30 ft
•
lbs
CONVERSIONS
in
•
lbs x 0.083 = ft
•
lbs
ft
•
lbs x 12 = in
•
lbs
ft
•
lbs x 0.1383 = kg
•
m
ft
•
lbs x 1.3558 = N
•
m
Part No. Description
07276 Adjustment Tool, Tilt Arm Parallelism
07277 Adjustment Tool, Tilt Arm Height Gage
07279 Installation Tool, Spider Bushing (#06459)
16421 Bearing Spool Tool (Constant Force)