Number: 006 /94
Date Issued: 9/1/94
Revised:
12/23/94
A fter m achining ro to rs ) with an on-car brake lathe, you m ust remove ail metal cuttings (particles) from
the A BS “toothed ring” (the reluctor) and the ABS sensor. Failure to remove these particles w ill pre
vent proper function of the ABS system.
f. if machining can not be achieved due to rotor thickness limitations, the dealer should replace the rotor. To
ensure a successful repair, run-out and/or DTV must be removed by on-car machining, even on new
rotor(s).
g. Install the wheel in the same location relative to the hub as it was originally positioned.
h. Torque wheel lug nuts to the specifications in the service manual.
i. Test drive the vehicle to confirm repair.
j. If the brake judder is still felt, correct the rear rotor(s) using steps “c” through Y .
SERVICE TO O LS
The Accu-Tum (model
8750)
On-Car Brake Lathe is recommended by Mazda Motor of America. The brake lathe
will be available soon from MMA’s National Accounts Program at a substantial savings. When the national
account is established, a Special Tools Service Bulletin will be released which will contain further details. How
ever,
if
you wish to receive a brochure on this
brake
lathe, please call
Accu-Tum
at
(800) 551-2228.
•W A R R A N TY INFORMATION
Applies To Vehicles Covered Under Normal Warranty
Parts No. O f Main Cause:
****
33 25*
**** 26 25*
(Rear of Vehicle - Rear Wheel Drive Only)
Location
Operation
Number
Labor
Hours
Front
One Side
P0113AMX
0.7
Both Sides
P0113BMX
1.2
Rear
One Side
P0214ARX
0.7
Both Sides
P0214BRX
1.2
NOTE:
1. Unnecessary replacement of rotors will result in warranty claim denial.
2. Brake pad replacement costs will not be warrantable for brake judder repair.
3. if an A ccu r-T u m on-car lathe is used, apply the labor tim e from the table above. If an off-car lathe is
used (until Jan.1, 1995), use the labor times from the 1994 SRT.The next issue of the S R T microfiche will
be revised to show the new labor times.
Page 2 of 2
Содержание 626 1989
