HomeLink should now activate your
rolling code equipped device.
NOTE
To program the remaining two HomeLink
buttons, begin with
“
Programming
”
―
step 2.
Do not repeat step 1.
For questions or comments, please contact
HomeLink at
www.homelink.com
or
1-
800-355-3515.
q
Gate operator/Canadian
Programming
Canadian radio-frequency laws require
transmitter signals to
“
time-out
”
(or quit)
after several seconds of transmission
―
which may not be long enough for
HomeLink to pick up the signal during
programming. Similar to this Canadian
law, some U.S. gate operators are
designed to
“
time-out
”
in the same
manner.
If you live in Canada or you are having
difficulties programming a gate operator
by using the
“
Programming
”
procedures
(regardless of where you live),
replace
“
Programming HomeLink
”
step 3
with
the following:
NOTE
If programming a garage door opener or gate
operator, it is advised to unplug the device
during the
“
cycling
”
process to prevent
possible overheating.
Continue to press and hold the HomeLink
button while you
press and release
―
every two seconds
(
“
cycle
”
) your hand-
held transmitter until the frequency signal
has successfully been accepted by
HomeLink. (The indicator light will flash
slowly and then rapidly.)
Proceed with
“
Programming
”
step 4 to
complete.
q
Operating the HomeLink System
Press the programmed HomeLink button
to operate a programmed device. The
code will continue being transmitted for a
maximum of 20 seconds.
q
Reprogramming the HomeLink
system
To program a device to HomeLink using a
HomeLink button previously trained,
follow these steps:
1. Press and hold the desired HomeLink
button.
DO NOT
release the button.
2. The indicator light will begin to flash
after 20 seconds. Without releasing the
HomeLink button, proceed with
“
Programming
”
- step 2.
q
Erasing Programmed HomeLink
Buttons
To erase the existing programming from
all three operating channels, press and
hold the two outside buttons (
,
)
on the auto-dimming mirror until the
HomeLink indicator light begins to flash
after approximately 20 seconds.
Verify that the programming has been
erased when you resell the vehicle.
Driving Your Mazda
Switches and Controls
5-73
Mazda6_8AS2-EC-09E_Edition1 Page223
Monday, June 1 2009 3:59 PM
Form No.8AS2-EC-09E
Содержание 2010 Mazda6
