background image

19

Reverse the  strike

1.

 Remove the door strike from the dryer door opening.

2.

  Remove the cosmetic screw opposite the door strike.

A

B

  

 

 

          A. Door strike 

B. Cosmetic screw

3. 

  Reinstall the door strike and cosmetic screw on the opposite 

side of dryer door opening from where they were removed.

      

NOTE:

 Door strike and plugs must be on the same side of the 

dryer door opening.

Reinstall the door

1.

 Remove the 4 screws and two hinges from the dryer door.

2

.

 Replace the 4 screws in the same holes

3.

  Remove the 4 screws from the opposite side of the door.

4. 

 Install the two hinges to the front panel of the dryer using  

4 screws. Use the non-slotted side to attach the hinge  

to the front panel.

5.

  

Install screws in top hinge holes in the door. Do not tighten 

screws. Leave approximately 1/4" (5 mm) of screw exposed

.

6. 

 Hang door by placing screw heads into top slotted holes of 

hinges and slide door down. Align bottom screw holes in hinge 

and door. Install two bottom screws. Tighten all hinge screws.

7. 

 Close door to engage door strike.

TROUBLESHOOTING

DRYER OPERATION

Dryer will not run

 

Has a household fuse blown, or has a circuit breaker 

tripped? 

There may be two household fuses or circuit breakers  

for the dryer. Check that both fuses are intact and tight,  

or that both circuit breakers have not tripped. Replace  

the fuse or reset the circuit breaker. If the problem  

continues, call an electrician.

 

Is the correct power supply available? 

Electric dryers require a 240-volt power supply. Check  

with a qualified electrician.

 

Was a regular fuse used? 

Use a time-delay fuse.

Содержание WED8200YW





















Отзывы: