background image

PRODUCT DIMENSIONS

Undercounter Dishwasher

PRODUCT MODEL NUMBERS

Because Whirlpool Corporation policy includes a continuous commitment to improve

our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specifications subject to change without notice.

Page 1 of 2

If connecting dishwasher with a power supply cord: 
Use power supply cord kit (Part

Number 4317824) marked for use

with dishwashers. Follow the kit

instructions for installing the power supply cord.
Power supply cord must plug into a grounded

 

prong outlet located in the cabinet next to

 

the 

dishwasher opening. Outlet must meet all local

 

codes and ordinances.
Water Supply Requirements:

 

A hot water line with 20 to

 

120 psi (138 to 862 kPa) water pressure. Water

 

temperature 

must be 120°F (49°C) water at dishwasher.

 

Use

 

3

/

8

" O.D. 

copper tubing with compression fitting or

 

flexible braided 

water supply line

.

 

Note:

 

" minimum plastic tubing is not recommended. 

Use a 90°

 

elbow with " hose connection with rubber

 

washer (

P

art 

N

umber W10273460). Do not solder 

within 6"

 

(15.2 cm) from water inlet valve.

Drain Requirements:A new drain hose is supplied with

your dishwasher. If this is not long enough, use a new 

drain

 

hose with a maximum length of 12' (3.7 m) (Part 

N

umber

 

3385556) that meets all current AHAM/IAPMO 

test

 

standards, is resistant to heat and detergent, and 

fits the 1"

 

(2.5 cm) drain connector of the dishwasher.

Make sure to connect the drain hose to waste tee or

 

disposer 

inlet above drain trap in house plumbing and 20"

 

(50.8 cm) 

minimum above the floor. It is recommended

 that the 

 

drain hose either be

 

looped 

up and securely

 

fastened to 

the underside of

 

the counter 

or be connected

 

to an air gap.

Make sure to use an air 

gap

 

if the drain hose is

 

connected to house

 

plumbing lower than 

20"

 

(50.8 cm) above 

subfloor or

 

floor. 

Use

 

1

/

2

" (1.3 cm) minimum I.D. drain line fittings.

If required, the air gap should be installed in accordance

 

with the air gap installation instructions. When connecting

the air gap

,

 a rubber hose (not provided) will be needed 

toconnect to the waste tee or disposer inlet.

air gap

      C

B. For panel-ready models, dishwasher

depth is 24" (60 cm) not including the

" (1.9 cm) custom door panel.

C. Door handles may protrude forward

of the face of the dishwasher; varies

by model.

A. Insulation may be compressed

(not used on all models).

             3 " - 4 "

(8.8 cm - 10.6 cm)

              For 4" (10 cm) 

       

toe

kick, height of 

cabinet

 

opening is 

34

1

/

2

" (86.3 cm).

    

24

"

(62.2 cm)

    B

    

23

"

(60.6 cm)

"

(1.9 cm)

      A

    

33

"

(85,1 cm)

min.

 with

  wheels

remo

ved

 

"

(9.4 cm)

    

21 "

(53.3 cm)

   30"

(76.2 cm)

MDB4949SD    

MDB

6

9

49

S

D

MDB

5

9

6

9SD    

MDB

7

9

4

9

S

D

Electrical Requirements:120-volt, 60 Hz, AC-only, 

15- or

 

20-amp. fused electrical supply. Copper wire only. 

A

 

time

 

delay fuse or circuit breaker and separate circuit 

is

 

recommended.

If direct wiring dishwasher: Use flexible, armored 

or

 

nonmetallic, sheathed copper

wire with grounding wire that

meets the wiring requirements for

your home and local codes and ordinances.

Use a UL Listed or CSA Approved conduit connector.

W10741197A

-D-MT

 

12

/

20

16

MDB89

6

9S

D

    

MDB89

5

9S

F

MDB89

7

9S

E

    

MDB8979S

F

Отзывы: