MAYAH FLASHMAN II Скачать руководство пользователя страница 11

Страница: 11 / 91

First Start > Battery Charger

Operating Manual for FLASHMAN II

this LED is switched off.

Error (Red LED):
Lights up when charger senses an error or when no battery is placed in the
charger. Possible errors are described below.

Charger errors:

Output voltage is out of operational range (9-12V)

Internal temperature of charger is out of range

Battery is faulty

2.3

Connectors

FLASHMAN II has got connectors on the top and bottom side.

Connectors on the top side

Slots

a) Slot for PCMCIA cards
In this slot the following cards can be inserted:

FLASHMAN II 3G/UMTS card for IP-transmission via 3G/UMTS

FLASHMAN II WLAN card for IP-transmission via WLAN

PC-Memory-card (for recording)

b) Slot for SD/SDHC card
In this slot any standard SD/SDHC card can be inserted as storage device for
recording.

c) Slot for FLASHMAN II battery
Here the original FLASHMAN II battery can be inserted. This battery enables a
mobile use of FLASHMAN II for a period of about 5 hours, depending on type of
use.

d) Ethernet connector
The RJ45 Ethernet connector can be used for IP-transmission via LAN and WAN.

e) USB connectors
FLASHMAN II has got two USB ports.
USB A-type port

Содержание FLASHMAN II




























































































Результаты поиска

Содержание FLASHMAN II

Отзывы:

Бренды по названию

Популярные бренды

MAYAH FLASHMAN II, Руководство по эксплуатации

Результаты поиска

Содержание FLASHMAN II

Отзывы:

Бренды по названию

Популярные бренды