ENGLISH
11
the direction to the handle (9) until click of the
lock (15) (fig. 2).
–
To remove the brush-attachment (14), press the
lock (15) and shift the attachment (14) (fig. 2).
Switching on
1.
Before operating the unit in steam ironing,
steaming or fabrics cleaning modes, make sure
that there is enough water in the tank (3)
2.
Unfold the base (5) towards the soleplate (1).
Place the unit on a flat heat-resistant surface.
3.
Insert the power plug into the mains socket.
4.
Use the control (12) to set ironing temperature,
depending on the type of fabric and operating
mode (see “Ironing temperature”), the indicator
(10) will light up.
5.
Once the soleplate (1) reaches the set tempera-
ture value, the indicator (10) will go out.
6.
Lift the unit and move the base (5) back to its
original position.
Operating the unit
–
During the operation always hold the unit only by
the handle (9).
–
To supply steam, press the button (6) intensive-
ly. Don’t press the button (6) more than three
times in a row, make at least a 10-15 second
interval between the pressings.
–
To avoid water dripping, watch the indicator (10),
press the button (6) if the indicator (10) is off.
Switching the unit off
7.
Switch the temperature control (12) to the “MIN”
position and unplug the unit.
8.
Put the unit on the base (5) and let it cool down
completely.
9.
Remove the plug (13), turn the unit over and
drain the remaining water from the tank (3).
VERTICAL STEAMING RECOMMENDATIONS
Garment care
–
Hang the clothes on a hanger.
–
Holding the hanging clothes, slightly press
the brush-attachment (14) to it and move the
attachment, pressing the steam supply button
(6) periodically. Steam gets deep into the fabric
and smoothes it, and the brush-attachment (14)
removes the stuck lint or fluff from your clothes.
–
Don’t take the clothes off the hanger right after
cleaning, wait some time to let it cool down.
Curtain care
–
Before cleaning curtains, they should be
smoothed to remove folds.
–
Clean curtains, using the brush-attachment
(14) and following the recommendations in the
«Garment care» section.
CLEANING AND CARE
–
Before cleaning, unplug the unit and let it cool
down completely.
–
Clean the unit with a soft, slightly damp cloth
and then wipe it dry.
–
Scale on the soleplate (1) can be removed with a
cloth soaked in vinegar-water solution.
–
After removing scale, polish the soleplate (1)
surface with a dry cloth.
–
Periodically wash the tank (3) with warm water.
–
The brush-attachment (14) can be washed in
warm water with a small amount of soft cleans-
er. After the brush dries, take it away for stor-
age.
–
Do not use solvents or abrasives for cleaning
the unit.
–
Do not immerse the unit, the power cord and
the power plug of the unit into water or other
liquids.
–
You can store the unit by hanging it on the loop
(8) provided that no water gets on the unit in
this position.
DELIVERY SET
Steam brush – 1 pc.
Brush-attachment – 1 pc.
Instruction manual – 1 pc.
TECHNICAL SPECIFICATIONS
Power supply: 220-240 V ~ 50 Hz
Power consumption: 800 W
The manufacturer preserves the right to change
the specifications of the unit without a preliminary
notification.
Unit operating life is 3 years
Guarantee
Details regarding guarantee conditions can be
obtained from the dealer from whom the appliance
was purchased. The bill of sale or receipt must be
produced when making any claim under the terms
of this guarantee.
This product conforms to the EMC-
Requirements as laid down by the Council
Directive 2004/108/ЕС and to the Low
Voltage Regulation (2006/95/ЕС)
MW-3708.indd 11
03.04.2014 11:30:43
