Maxwell MW-3704 VT, Инструкция по эксплуатации

Страница: 9 / 40

ENGLISH
9
•
Install and remove the brush-attachment only
after the unit has cooled down completely.
•
Never pull the power cord, when disconnect-
ing the unit from the mains; take the power
plug and carefully pull it out of the socket.
•
Do not disassemble the unit by yourself, if any
malfunction is detected or after the unit was
dropped, apply to the nearest authorized ser-
vice center.
•
Transport the unit in the original package only.
•
Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
Unit purpose
The garment steamer can be used for any types
of fabrics and for smoothing folds on clothes. If
you have doubts about steaming any certain kind
of fabric or clothes, you should follow the recom-
mendations on the product label. If such informa-
tion is not available, try to steam the fabric from
the backside.
When steaming such fabrics as silk or corduroy,
keep the garment steamer some distance away
from the material.
Use the brush-attachment (5) to remove lint or
threads from the fabric.
Before the first use
After unit transportation or storage at low
temperature it is necessary to keep it for at
least two hours at room temperature before
switching on.
– Unpack the unit, remove any stickers that can
prevent unit operation.
– Make sure that the operating voltage of the
unit corresponds to the voltage of your mains.
– Wipe the garment steamer body with a slightly
damp cloth and then wipe it dry.
– Open the water inlet lid (3), fill the water tank
(4) with water (pic. 3), then close the lid (3)
tightly. Wipe water drops on the unit body with
a dry cloth.
– Insert the power plug into the mains socket,
the indicator (6) will light up.
– The unit is ready to operate when the indicator
(6) goes out.
– Take the garment steamer with your hand and
hold it in the area of the steam supply button
(2). To switch the steam supply on, press and
hold the button (2).
– To clean the steam chamber, direct the outgo-
ing steam on a kitchen towel, for instance, and
try to smooth it.
– After the unit operation unplug the garment
steamer and let it cool down.
Water selection
Use tap water to fill the water tank (4). If tap water
is hard, it is recommended to mix tap water with
distilled water in proportion 1:1, if tap water is too
hard, mix it with distilled water in proportion 1:2 or
use distilled water only.
Steamer operation
– Set the brush-attachment (5) on the garment
steamer (pic. 1).
Attention!
– Do not plug the garment steamer in if the
water tank (4) is empty.
– Unplug the unit and wait till it cools down
before installing or removing the brush-
attachment (5).
– To remove the brush-attachment (5), pull
the lock of the brush-attachment (5) (pic.
2).
– Open the water inlet lid (3), fill the water tank
(4) with water (pic. 3), then close the lid (3)
tightly.
Attention!
– Before filling the water tank (4) with water,
make sure that the unit is unplugged.
– Make sure that water drops do not get onto
the garment steamer body, the power cord
or the power plug.
– Do not exceed the «max» mark when filling
the water tank (4) with water.
– Do not fill the water tank (4) with carbon-
ated water, perfume additives, vinegar,
chemical agents etc.
– If you need to refill water during operation,
switch the garment steamer off by unplug-
ging it and wait till the unit cools down
completely.
– Hang the clothes on a hanger.
Note: - Never steam clothes on a person as the
outgoing steam temperature is very high, use a
hanger only.
– Insert the power plug into the mains socket,
the indicator (6) will light up.
– When the unit is ready for operation, the indi-
cator (6) will go out.
MW-3704.indd 9 05.11.2013 11:11:55