![background image](http://html1.mh-extra.com/html/maxwell/mw-3508-gy/mw-3508-gy_manual-instruction_1746344008.webp)
8
ENGLISH
Stand fan
description
1. Front grid
2. Fixing ring
3. Blade clamp
4. Blades
5. Rear grid fastening nut
6. Rear grid
7. Electric motor axis
8. Fan body
9. Display
10. Control panel
11. Fan body clamp
12. Telescopic bar
13. Telescopic bar clamp
14. Stand
15. Decorative panel
16. Base
17. Remote control
Control panel
18. Radio receiver On/Off button
19. On/Off/Speed selection button
20. Operation mode selection button
21. Timer setting button
22. Horizontal oscillation On/Off button
23. Radio stations scanning button
display
24. Radio receiver power indicator
25. “Abating wind” mode indicator
26. “Natural wind” mode indicator
27. «Standard» mode indicator
28. Speed mode indicator
29. Timer settings indicator
30. Horizontal oscillation mode indicator
31. Room temperature indication
32. Radio stations scanning indicator
Remote control (RC)
33. Fan On/Off button
34. Radio receiver On/Off button
35. Timer setting button
36. Horizontal oscillation On/Off button
37. Volume control button
38. Radio stations scanning button
39. Speed mode selection button
40. Operation mode selection button
attention!
For additional protection it is reasonable to install a
residual current device (RCD) with nominal operation
current not exceeding 30 mA. To install RCD contact
a specialist.
SafEtY MEaSURES
Before using the unit, read these instructions carefully.
Keep these instructions for future reference.
Use the unit for intended purposes only, as specified in
this manual. Mishandling the unit can lead to its break-
age and cause harm to the user or damage to his/her
property.
•
Before using the unit for the first time, make sure
that voltage in your mains corresponds to unit oper-
ating voltage.
•
Place the fan on a flat and steady surface.
•
Do not use the fan outdoors.
•
Do not switch the fan on without the installed pro-
tective grid and floor base.
•
Do not insert any foreign objects into the fan pro-
tective grids to avoid injuries or unit damage.
•
Do not touch rotating blades during fan operation.
•
Do not use the fan in bathrooms or in rooms with
high humidity.
•
Do not place the fan on surfaces, where it can fall in
a bath or other container, filled with water.
•
If the fan fell into water unplug it before touching
and only then take the unit out of the water.
•
Do not place the fan near blinds, curtains or house
plants.
•
Do not switch the fan on with wet hands to avoid
electric shock.
•
Never leave the operating unit unattended.
•
Unplug the fan before cleaning or when you do not
use it.
•
When unplugging the unit pull the plug but not cord.
•
For children safety reasons do not leave polyethyl-
ene bags, used as a packaging, unattended.
Attention! Do not allow children to play with polyethyl-
ene bags or packaging film. Danger of suffocation!
•
Never allow children to use the fan as a toy.
•
Close supervision is necessary when children or
disabled persons use the fan.
•
This unit is not intended for usage by children or
disabled persons unless they are given all the nec-
essary and understandable instructions by a person
who is responsible for their safety on safety mea-
sures and information about danger that can be
caused by improper usage of the unit.
•
It is not recommended to stay under the air flow
from the fan for a long time (especially for children
and elderly people).
•
Never use the fan if the power cord or the plug are
damaged, if the fan operates improperly, after it
was dropped or damaged in some other way. In
this case contact the authorized service center for
checking or repairing the unit.
THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY
Before the first use
In case of unit transportation or storage at low tem-
perature it is necessary to keep it for at least two
hours at room temperature before switching on.
The fan is supplied disassembled. Do not plug the fan
in if you haven’t assembled it.
–
Unpack the unit and remove any stickers that can
prevent unit operation.
–
Make sure that the voltage of the mains corre-
sponds to the operating voltage of the unit.
–
Insert the plastic legs and assemble the base (16),
install the base (16) on a flat dry surface (pic. 1).
MW-3508_IM.indd 8
25.11.2013 16:47:36
Содержание MW-3508 GY
