![background image](http://html1.mh-extra.com/html/maxwell/mw-1252/mw-1252_manual-instruction_1746443004.webp)
4
ENGLISH
4
4
Do not try to mince material with hard fiber like
•
ginger or horseradish.
To avoid block and jams inside the feeder
•
screw, avoid using excessive force to push
meat.
If the unit gets blocked due to hard materials
•
lodged on to the feeder screw or cutting blade,
immediately switch off the unit and remove the
ingredient before starting again.
To switch to the REVERSE mode, switch off the
•
unit, setting the switch (7) to the “0” position,
then set the switch (6) to the “
” position and
after 5-6 seconds pause, set the switch (7) to
the “R” position, after removing the blockage
set the switch (7) to the “0” position, and the
switch (6) to the
position.
This unit is equipped with overheating protec-
•
tion system. The system is intended for protec-
tion of electric motor from overheating and al-
lows prolonging its service life.
If during operation rotation of the mixing screw
•
(8) and the blade (9) suddenly stopped:
- set the switch (7) to the “0” position, and take
the plug out of the socket.
- let the unit cool down for 50-60 minutes.
- switch on the mincer again
Note:
- If the protection system actuates very often,
apply to the authorized service center.
PREPARATION OF THE MEAT MINCER
Before first use, please remove all packaging
•
material from the unit and wipe the body with
a damp cloth.
Wash all removable parts in warm water with
•
neutral detergent, rinse and dry thoroughly
before assembling the unit.
OPERATING THE MEAT MINCER
(general provisions)
The meat mincer is intended to mince bone-
•
less meat for household use only.
Before using the appliance for the first time,
•
make sure that voltage in your mains corre-
sponds to the voltage specified on the unit.
After assembling the unit, place the mincer on
•
a flat dry surface.
Please ensure that the ventilation openings on
•
the body are not blocked.
Insert the plug into the socket.
•
Place a bowl under the mincer head (3).
•
Please ensure that the meat is thawed thor-
•
oughly before mincing. Check the meat for
bones and excess of fat. Clean the meat and
cut into small cubes to fit the food tray. (2).
Switch on the unit, setting the switch (7) to the
•
“ON” position, the switch (6) should be in the
position.
Slowly feed the meat pieces into the food fun-
•
nel (3) using the pusher (1).
Use only the pusher (1), supplied with the unit.
•
Do not use foreign objects to push meat. Never
•
use your fingers to push the food down.
Do not apply excessive force when pushing
•
down the products.
Do not run the appliance for more than 5 min-
•
utes continuously.
After 5 minutes of continuous use, allow the
•
appliance to cool down before further opera-
tion.
After you finish operating the unit, switch of the
•
unit setting the switch (7) to the “0” position
and unplug it, only then you can start disas-
sembling it.
MEAT MINCING
1. Insert the mincing screw (8) into the mincer
head body (3), set the crossed blade (9), se-
lect the required grate (10, 11,12) and set it
above the blade, by matching the grooves on
the grate with the clamp on the mincer head
(3), tighten the nut (13).
Attention!
-
The meat will not be minced if the blade
is mounted with the wrong side facing the
screw (cutting side to the mixing screw).
- Do not tighten the nut strongly (13); tight-
en it completely after setting the head on
the mincer.
- Course (10) grates and medium grates
(11) suit for processing raw meat, fish and
ready products, vegetables, dried fruits,
cheese, etc.
2. Set the mincer head (3) turn it anti clockwise
until it is fixed.
3. Tighten the nut completely (13).
4. Set the food tray (2) on the mincer head (3).
MW-1252.indd 4
MW-1252.indd 4
22.06.2011 17:51:09
22.06.2011 17:51:09
Содержание MW-1252
Страница 1: ...MW 1252 indd 1 MW 1252 indd 1 22 06 2011 17 51 08 22 06 2011 17 51 08...
Страница 47: ...2011 GOLDER ELECTRONICS LLC 2011 MW 1252 indd 47 MW 1252 indd 47 22 06 2011 17 51 12 22 06 2011 17 51 12...
Страница 48: ...MW 1252 indd 48 MW 1252 indd 48 22 06 2011 17 51 12 22 06 2011 17 51 12...