Maxon TUK-A-WAY 80-3LM Скачать руководство пользователя страница 25

Страница: 25 / 36

11921

Slauson

Ave.

Santa

Springs,

CA.

90670

(800)

227-41

(888)

771-7713

PAGE 25

POWER CABLE INFORMATION

A proper crimp is one which does not have an air gap between the cable

and the copper end fittings after crimping. The crimped end fitting shall not

have any cracks.

Proper sized crimping dies shall be used with a hydraulic or manual

crimping tool. Crimping dies which are struck with a hammer are not accept-

able for initial installation, and should be used only in the case of an emer-

gency repair. Heat Shrink tubing is provided and must be installed at each end

fitting.

CRIMPING

For Trucks, route the cable along the chassis frame flange. Use caution

when routing through or around chassis cross members to avoid sharp edges

which could wear through the cable jacket.

MAXON

supplies cable installation

clips as shown in

Fig. 1

For Trailers, clamps are provided in the Trailer Kit and can be bolted to

the trailer cross members. This allows the cable to run under the cross mem-

bers. See

Fig. 2

Extra Heavy Duty

Crimping Tool

Never use a Hammer to flatten

the End Fitting when installing

on Power Cable

ROUTING

FIGURE 1

FIGURE 2

2 to 3

Cable

Clamp

Heat Shrink Tubing

Содержание TUK-A-WAY 80-3LM





































Результаты поиска

Содержание TUK-A-WAY 80-3LM

Отзывы:

Похожие инструкции для TUK-A-WAY 80-3LM

Бренды по названию

Популярные бренды

Maxon TUK-A-WAY 80-3LM, Руководство по установке

Результаты поиска

Содержание TUK-A-WAY 80-3LM

Отзывы:

Похожие инструкции для TUK-A-WAY 80-3LM

Бренды по названию

Популярные бренды