Maxon TUK-A-WAY 80-3LM Скачать руководство пользователя страница 10

Страница: 10 / 36

11921

Slauson

Ave.
Santa

Fe
Springs,

CA.

90670

(800)

227-41

16
F

AX
(888)

771-7713

PAGE 10

WELD LIFTGATE TO VEHICLE

Place a C Clamp on

each side of the Platform as

shown to prevent the Hoist

Chain from slipping off of the

Platform. Tack weld two (2)

temporary support straps to

the Extension Plate to align

the Platform. Place chain en-

tirely around the Platform, then

hoist and jack the unit into

position. The rear edge of the

Platform must be flush with the

Extension Plate. The Hinge Pins must be 90° to the vehicle bed.

Floor Jack

Hinge Pins

Support Straps

Hoist

90°

The rear edge of the Platform must be level with and flush against the

Extension Plate. The edges of the Platform should be equally spaced inboard

from the ends of the Extension Plate. Tack weld the two (2) temporary Exten-

sion Plate support straps to the Extension Plate.

Support Strap

Platform

Rear Edge of

Platform

Tack Weld to

Extension Plate,

close to the Edge.

(Typ.)

Equal Spaces

Extension Plate

Weld, see

following

page.

Approx. 1

Overhang

(Typ)

Содержание TUK-A-WAY 80-3LM





































Результаты поиска

Содержание TUK-A-WAY 80-3LM

Отзывы:

Похожие инструкции для TUK-A-WAY 80-3LM

Бренды по названию

Популярные бренды

Maxon TUK-A-WAY 80-3LM, Руководство по установке

Результаты поиска

Содержание TUK-A-WAY 80-3LM

Отзывы:

Похожие инструкции для TUK-A-WAY 80-3LM

Бренды по названию

Популярные бренды