manualshive.com logo in svg

maxon motor EPOS2 24/5, Справочник по аппаратуре, Страница: 37 / 44

Поделиться
Скачать
maxon motor EPOS2 24/5 Скачать руководство пользователя страница 37

maxon motor control
EPOS2 Positioning Controller

Document ID: rel5190

4-37

EPOS2 24/5 Hardware Reference

Edition: October 2014

© 2014 maxon motor. Subject to change without prior notice.

4.10

Status LEDs 

The LEDs display the current status of the EPOS2 24/5 as well as possible errors:

•

Green LED shows the operating status

•

Red LED indicates errors

For detailed information 

separate document «EPOS2 Firmware Specification».

Table 4-17

LEDs – Interpretation of Condition

LED

Status / Error

Red

Green

OFF

Slow

Power stage is disabled. Device is in status…
• “Switch ON Disabled”
• “Ready to Switch ON”
• “Switched ON”

OFF

ON

Power stage is enabled. Device is in status…
• “Operation Enable”
• “Quick Stop Active”

ON

OFF

FAULT state. Device is in status…
• “Fault”

ON

ON

Power stage is enabled. Device is in temporary status…
• “Fault Reaction Active”

ON

Flash

No valid firmware or firmware download in progress.

Flash = Flashing (

≈

0.9 s OFF/

≈

0.1 s ON)

Slow = Slow blinking (

≈

1 Hz)

Содержание EPOS2 24/5













































Отзывы:

Нет отзывов