background image

DS3232

Extremely Accurate I

2

C RTC with 

Integrated Crystal and SRAM

8

_____________________________________________________________________

Block Diagram

N

N

RST

V

CC

INT/SQW

CLOCK AND CALENDAR

REGISTERS

SRAM

USER BUFFER

(7 BYTES)

I

2

C INTERFACE AND

ADDRESS REGISTER

DECODE

POWER CONTROL

V

CC

V

BAT

GND

SCL

SDA

TEMPERATURE

SENSOR

CONTROL LOGIC/

DIVIDER

SQUARE-WAVE BUFFER;

INT/SQW CONTROL

CONTROL AND STATUS

REGISTERS

VOLTAGE REFERENCE;

DEBOUNCE CIRCUIT;
PUSHBUTTON RESET

OSCILLATOR AND 

CAPACITOR ARRAY

X1

X2

DS3232

32kHz

Detailed Description

The DS3232 is a serial RTC driven by a temperature-
compensated 32kHz crystal oscillator. The TCXO pro-
vides a stable and accurate reference clock, and
maintains the RTC to within ±2 minutes per year accu-
racy from -40°C to +85°C. The TCXO frequency output
is available at the 32kHz pin. The RTC is a low-power
clock/calendar with two programmable time-of-day
alarms and a programmable square-wave output. The

INT

/SQW provides either an interrupt signal due to

alarm conditions or a square-wave output. The clock/cal-
endar provides seconds, minutes, hours, day, date,
month, and year information. The date at the end of the
month is automatically adjusted for months with fewer
than 31 days, including corrections for leap year. The
clock operates in either the 24-hour or 12-hour format
with an 

AM

/PM indicator. The internal registers are

accessible though an I

2

C bus interface.

A temperature-compensated voltage reference and
comparator circuit monitors the level of V

CC

to detect

Содержание Maxim DS3232 Series




















Отзывы: